Transmission method, Half-Duplex | Crestron electronic CP-X8150

6. Network Bridge Function

6.4 Transmission method

The transmission method can be selected from the menus, only when the NETWORK BRIDGE is selected for the COMMUNICATION TYPE. (OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

HALF-DUPLEX  FULL-DUPLEX

6.4.1 HALF-DUPLEX

This method lets the projector make two way communication, but only one direction, either transmitting or receiving data, is allowed at a time.

The method does not allow the projector to receive the data from the computer while waiting for response data from an external device. After the projector receives the response data from an external device or the response limit time is past, the projector can receive the data from the computer.

That means that the projector controls transmitting and receiving the data to synchronize the communication.

To use the HALF-DUPLEX method, set up the RESPONSE LIMIT TIME following the instructions below.

TCP/IP data	Protocol change	Serial data
Wired LAN		RS-232C
LAN cable	RS-232C cable		External device
Computer			External device
Computer
Wireless LAN
Transmitting data
	Transmitting data
Discarding data	Response limit
Discarding data	time

	Response data
Response data	Transmitting data
	Transmitting data

Using the RESPONSE LIMIT TIME menu, set the waiting time for response data from an external device. (OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

OFF  1s  2s  3s ( OFF)

54

Image 54

Crestron electronic CP-X8150, CP-WX8240 user manual Transmission method, Half-Duplex

Contents

Features Thank you for purchasing this productTrademark acknowledgment Connection to the network ContentsManual network connection setting Wireless LAN Network Presentation Web Control Network Bridge Function Other Functions Security precautions when using wireless LAN Do not USE Near the Following Required equipment preparation Connection to the networkSystem requirements Hardware and software requirement for computer Quick connection System requirements Network settings Manual network connection setting Wired LANThis section explains how to set it up manually Equipments connection Manual network connection setting Wired LAN About IP address Setting manually Setting automatically Internet Option setting Manual network connection setting Wireless LAN Preparation for wireless LAN connection Manual network connection setting Wireless LAN Wireless LAN connection set upWireless About IP address Manual network connection setting Wireless LAN Network Presentation Web Control User name Password Administrator Blank Projector Web ControlLogon LAN Projector Web ControlNetwork Information Dhcp Displays and configures network settings AMX D.D Projector Web Control Network Settings Dhcp onDhcp OFF Enables Dhcp Disables DhcpWeb Control Port Settings Displays and configures communication port settings Projector Web Control Port Settings Click the Apply button to save the settings Mail Settings Displays and configures e-mail addressing settingsSend Test Mail Alert Settings Displays and configures failure & alert settings Except Cold Start and Authentication Failure Alarm TimeOnly Lamp Time Alarm and Filter Time Alarm Snmp Trap Schedule Settings Displays and configures schedule settings Description Schedule Date Month/DayMessenger Projector Web Control Schedule Settings Date/Time Settings Displays and configures the date and time settingsFirst, 2, 3, 4, Last Sntp Projector Web Control Date/Time SettingsTime difference Sntp Server Address Security Settings Snmp Projector Control Projector Web Control Projector Control ECO Mode Setup Auto KeystoneAuto ECO Mode Installation Audio Source Audio VolumeSpeaker Audio Source LAN Shade Timer Direct Power onAuto Power OFF Option Source Skip Front ServiceRemote Receiv Rear Remote Control Projector Web Control Remote Control Network Restart Displays the settings and status of the projectorProjector Status Restarts the projector’s network connection Crestron e-Control Clicking the corresponding tab at the top rightWindow Crestron e-Control Main windowSources List Crestron e-Control- Main window Tools window Crestron ControlProjector Admin Password Projector Configures the network settings of the projectorUser Password Crestron e-Control- Tools window Info window Projector Information Help Desk window Emergency Alert My Image Function OPTION menu in the Operating Guide Messenger Function Operating Guide Technical Connecting devicesNetwork Bridge Function LAN port USB Type a port Control port Control port Communication setupCommunication port Condition Transmission method HALF-DUPLEX Transmission method FULL-DUPLEX Mail Settings &24 Other FunctionsMail Alerts Mail Alerts Projector Management using Snmp Snmp Settings &23 Event Scheduling Schedule Settings &27 Event Scheduling Date/Time Settings &30 Command Control via the Network Following two ports are assigned for the command controlCommunication Port Command Control via the Network Header Data length RS-232Ccommand Check Sum Connection Command FormatReply Error code TCP #9715 Reply Data format Authentication Automatic Connection Break Crestron RoomView Troubleshooting Problem Likely Cause Things to Check Specifications Warranty and after-sales service