Removing a Dual Slot Hard-Drive Blank | Dell E19S, R520 manual

Figure 21. Hard-Drive Blank Installation Sequence

Removing A Dual Slot Hard-Drive Blank

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have hard-drive blanks installed.

NOTE: Systems configured for software RAID support only four hard drives. The remaining hard-drive slots are pre- installed with dual slot hard-drive blanks, and are not available for software RAID.

NOTE: This is a service only procedure.

1.If installed, remove the front bezel.

2.Using a screwdriver, push the release tabs to unlock the dual slot hard-drive blank from the chassis.

3.Pull the hard-drive blank at the corners until it is free of the hard-drive slot.

50

Image 50

Dell E19S, R520 owner manual Removing a Dual Slot Hard-Drive Blank, Hard-Drive Blank Installation Sequence

Contents

Regulatory Model E19S Series Regulatory Type E19S001 Dell Inc. All Rights Reserved Contents Installing Memory Modules Installing System ComponentsMemory Optimized Independent Channel Mode Installing a Dual Slot Hard-Drive Blank Installing The Power Supply Blank Installing The Optical DriveExpansion-Card Installation Guidelines Internal USB Memory Key Optional 111 When To Use The Embedded System Diagnostics101 123 113117 141Page Front-Panel Features And Indicators Indicator, Button, or Icon Description Connector Use this button only if directed to do so by qualified Front and the system status indicator on the backUSB connectors Support personnel or by the operating systems Button Description LCD Panel FeaturesHome Screen Setup Menu View Menu Off Hard-Drive Indicator PatternsDrive-Status Condition Indicator Pattern RAID Only Seconds Connects a PCI Express expansion card Back-Panel Features And IndicatorsConnector Through the optional cable management arm Compliant NIC Indicator Codes Power Indicator Codes Power supply and that the power supply is operational AC power supply status indicator/handleDC power supply status indicator Flashing amber Indicates a problem with the power supply Power Indicator Codes For Non-Redundant Power Supply Diagnostic Indicator Condition Pattern Green Other Information You May Need F10 Choosing The System Boot ModeKeystroke Description F11 F12 Using The System Setup Navigation Keys Entering System SetupResponding To Error Messages System Bios Screen System Setup OptionsSystem Setup Main Screen System Information Screen Memory Settings Screen Processor Settings Screen Execute Disable Option is set to EnabledPrefetcher option is set to Enabled Execute Disable option is set to Enabled Integrated Devices Screen Sata Settings ScreenBoot Settings Screen Serial Communications Screen System Profile Settings Screen System Security Screen System And Setup Password Features Miscellaneous Settings Assigning a System And/Or Setup Password Operating With a Setup Password Enabled Entering The Uefi Boot ManagerUsing Your System Password To Secure Your System Boot Manager enables you to Using The Boot Manager Navigation Keys Boot Manager Screen Entering The iDRAC Settings Utility IDRAC Settings UtilityUefi Boot Menu Changing The Thermal SettingsPage Page Front Bezel Optional Installing The Front BezelRecommended Tools Release latch Opening The System Opening And Closing The SystemRemoving The Front Bezel Keylock Front bezel Locking hook System cover Latch Latch release lock Inside The SystemClosing The System DIMMs Cooling shroud Cooling fans Expansion-card latchHeat sink for processor Inside the System-Non-Redundant Power Supply Unit Chassis Cooling Shroud Removing and Installing the Cooling Shroud Removing The Cooling Shroud 1333, 1066, Dual rank Installing The Cooling ShroudSystem Memory 1333, 1066 Dual rank Quad rank Memory channels are organized as follows Processor Advanced ECC Lockstep General Memory Module GuidelinesMode-Specific Guidelines Memory Sparing Memory Optimized Independent Channel ModeSample Memory Configurations Memory Mirroring 2R x4, 1600 MT/s B3, B4, B5, B6 2R x4, 1600 MT/s 2R x4, 1333 MT/s2R x4, 1600 MT/s B4, B5 192 2R x4, 1333 MT/s 384 4R x4, 1066 MT/s Removing Memory Modules256 4R x4, 1066 MT/s Installing Memory Modules Removing The Memory Module Installing The Memory Module Hard Drives Hard-drive blank Release button Installing a 3.5 Inch Hard-Drive BlankRemoving a 3.5 Inch Hard-Drive Blank Hard-Drive Blank Installation Sequence Removing a Dual Slot Hard-Drive Blank Dual slot hard-drive blank Release tabs Installing a Dual Slot Hard-Drive BlankRemoving a Hot-Swap Hard Drive Installing a Hot-Swap Hard Drive Release button Hard drive Hard-drive carrier handle Screws Inch hard-drive adapter Inch hard drive Hard-drive carrier Screws Hard drive Screw holes Hard-drive carrier Screws Hard-drive adapter Inch hard drive Removing The Optical Drive Optical drive Power and data cable Release tabOptical Drive Optional Removing a Cooling Fan Installing The Optical DriveCooling Fans Installing a Cooling Fan Removing and Installing a Cooling Fan Internal USB Memory Key Optional Replacing the Internal USB Key Expansion Card Slots Expansion-Card Installation GuidelinesExpansion Cards And Expansion-Card Risers Riser External RAID CNAs Gb NICs Removing An Expansion CardCard Priority Card Type Gb NICs Non-RAID Expansion card Expansion-card latch Riser Installing An Expansion Card Riser Expansion-card latch Expansion card Expansion-card riser Release tabs Riser guide pins Connector Removing Expansion-Card Risers IDRAC Ports Card Optional Installing Expansion-Card RisersExpansion-card riser Connector Riser guide pins Removing The iDRAC Ports Card Installing The iDRAC Ports Card Removing and Installing the iDRAC Ports Card Replacing An SD vFlash Card SD vFlash CardInternal Dual SD Module Removing The Internal Dual SD Module Blue pull tab Dual SD module SD card Internal SD Card Installing The Internal Dual SD ModuleInstalling An Internal SD Card Removing An Internal SD Card Integrated Storage Controller Card Removing The Integrated Storage Controller Touch-points Release levers Storage-controller card Installing The Integrated Storage ControllerStorage connector on the system board Processors Removing a Processor Removing and Installing the Heat Sink Notches in processor Socket keys Installing a ProcessorProcessor ZIF socket Processor shield Power Supplies Removing An AC Power Supply Connector Power supply Release latch Power supply handle Supply voltage -48-60 V DC Current consumption 32 a maximum Installing An AC Power SupplyWiring Instructions For a DC Power Supply Safety ground wire Grounding post #6-32 nut Locking washer DC power socket Wire -48 Rubber cap Wire RTN Captive screws DC power connector Connector Release latch Power supply Removing a DC Power SupplyInstalling a DC Power Supply Power supply status indicator Power supply blank Removing The Power Supply BlankInstalling The Power Supply Blank Removing The Power-Distribution And Power-Interposer Boards Power-distribution board Power-interposer board Release tab Power-Distribution Board Connectors Power-Interposer Board Connectors Removing a Non-Redundant Power Supply Removing and Installing a Non-Redundant Power Supply Standoff on the chassis Installing a Non-Redundant Power Supply Removing The Redundant Power Supply Unit Divider Installing The Redundant Power Supply Unit Divider Redundant power supply unit divider System battery Battery connector Locate the battery socket System BatteryReplacing The System Battery Hard-Drive Backplane Removing The Hard-Drive Backplane Backplane signal connector Securing hooks System board Installing The Hard-Drive Backplane Signal cable connector SAS a cable connector Control-panel board Screws Control-panel data cable Control Panel AssemblyRemoving The Control-Panel Board USB cable Installing The Control-Panel BoardRemoving The Control Panel Notches on chassis front wall Control panel Installing The Control PanelSystem Board Removing The System Board Release screws System board holder Installing The System BoardUnpack the new system board assembly Page Troubleshooting a USB Device Troubleshooting External ConnectionsTroubleshooting The Video Subsystem Troubleshooting a Serial I/O Device Troubleshooting a NIC Troubleshooting a Wet System Troubleshooting a Damaged System Troubleshooting The System Battery Troubleshooting Power Supplies Troubleshooting System Memory Troubleshooting Cooling ProblemsTroubleshooting Cooling Fans Reseat the memory modules in their sockets Close the system Troubleshooting An Internal USB KeyTroubleshooting An SD Card 106 Troubleshooting An Optical Drive Troubleshooting a Hard Drive Troubleshooting a Storage Controller Troubleshooting Expansion Cards Troubleshooting Processors Running The Embedded System Diagnostics Dell Online Diagnostics Dell Embedded System DiagnosticsWhen To Use The Embedded System Diagnostics 112 System Diagnostic ControlsLeast one event description is recorded System Board Jumper Settings Jumper Setting Description System Board Connectors Connector Description Disabling a Forgotten Password Page Expansion Bus Memory Front Connectors BackDrives Internal Environmental Temperature Temperature Continuous Operation Maximum Vibration EnvironmentalRelative Humidity Maximum Shock Gaseous Contamination 122 Viewing LCD Messages System Error MessagesLCD Messages Removing LCD Messages Details Error CodeAMP0302 Message Action BAT0017 Message ASR0003 MessageBAT0002 Message CPU0000 Message CPU0204 Message CPU0010 MessageCPU0023 Message CPU0700 Message CPU0704 Message CPU0702 MessageCPU0703 Message FAN0000 Message If the issue persists, see Getting HelpAction Reinstall or reconnect the hardware HWC2003 Message Details Fan operating speed is out of range Action MEM0007 Message MEM0000 MessageMEM0001 Message MEM0701 Message PCI1302 Message MEM1208 MessageMEM8000 Message PCI1304 Message PCI1348 Message PCI1320 MessagePCI1342 Message PCI1360 Message PSU0001 Message PST0128 MessagePST0129 Message PSU0002 Message PSU0031 Message PSU0006 MessagePSU0016 Message PSU0032 Message PSU0036 Message PSU0034 MessagePSU0035 Message PSU0037 Message Configuration and power consumption PSU1201 Message Power supply redundancy is lost DetailsSystem power inventory change System power consumption RFM2001 Message RFM1014 MessageRFM1201 Message RFM2002 Message Power. If problem persists call support SEL0006 Message All event logging is disabled DetailsAppear if the user disabled event logging Security may be compromised Failures Issues persists, contact supportFailed TMP0121 Message Reinstall system cables Diagnostic MessagesReview system logs for power supply exceptions Alert Messages 140 Getting Help Contacting Dell