Dell GX1 P manual 8WLOLW\LVNHWWHLQWRGULYH$, Nhwwhgulyh, Ruprgli, Glvnhwwh

7DEOH￿%￿￿￿￿￿&RQILJXUDWLRQ￿8WLOLW\￿0HVVDJHV￿￿FRQWLQXHG￿

0HVVDJH	3UREDEOH￿&DXVH	&RUUHFWLYH￿$FWLRQ
The configuration	This message appears	You can get a copy of the configuration file from
(.cfg) file used by	when you try to add a	the original ISA Configuration Utility Diskette that
the ICU for this	listed card and the config-	you used to create the backup ICU diskette. Use
card is now invalid	uration file for this card	the following procedure:
or does not exist.	has been corrupted or
Do you wish to load	deleted from the data-	￿￿	,QVHUW￿WKH￿RULJLQDO￿,6$￿&RQILJXUDWLRQ￿
the file?	base.		8WLOLW\￿'LVNHWWH￿LQWR￿GULYH￿$￿
No configuration	This message appears	￿￿	&KDQJH￿WR￿WKH￿GE￿VXEGLUHFWRU\￿RQ￿WKH￿GLV￿
(.cfg) file exists	when you modify a card		NHWWH￿GULYH￿
for the card being	and its configuration file
modified. Do you	does not exist or has		For example, type cd a:\db.
want to load one?	been deleted.
		￿￿ 8VH￿D￿WH[W￿HGLWRU￿WR￿VHDUFK￿WKH￿LFX￿QG[￿ILOH￿
			IRU￿WKH￿FDUG￿,'￿RI￿WKH￿FDUG￿\RX￿ZDQW￿WR￿DGG￿
			RU￿PRGLI\￿
			The name of the configuration file is part of
			this card ID. For example, if the card ID is
			ICU0200, the configuration file is !icu0200.cfg.
		￿￿ &RS\￿WKH￿FRQILJXUDWLRQ￿ILOH￿IURP￿WKH￿
			RULJLQDO￿,&8￿GLVNHWWH￿WR￿WKH￿EDFNXS￿
			GLVNHWWH￿￿
This is an EISA	This message appears if	To use the ICU, you must load the utility onto a
system. Use an ECU,	you attempt to run the	non-EISA system.
not the ICU, to	ICU on an EISA system.
configure your
system.

You have added a card using settings different from fac- tory default. Reconfigure the card to the set- tings in the next display (see the card’s manual) before installing it.

This message can appear in two situations:

‡You added an ISA expansion card, selected OK, and the ICU had to use resource values dif- ferent from the card’s defaults to avoid conflicts.

‡You added an ISA expansion card, selected Advanced, and chose resource values different from the card’s defaults.

Make note of the new card configuration shown in the Card Resource Usage dialog box displayed after this message. Change jumper settings on the ISA expansion card to match the new card configuration.

NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in the online System User’s Guide.

ISA Configuration Utility Messages B-5