Delta DT3 instruction sheet 999 ~ 9,999

1006H	Heating/Cooling control selection	Refer to Ouputput Mode Selection
1007H	1st group of Heating/Cooling	1~990, unit is 0.1 second. When the output setting = realy, the minimum control
	control cycle	cycle is 5 second
1008H	2nd group of Heating/Cooling	1~990, unit is 0.1 second. When the output setting = realy, the minimum control
	control cycle	cycle is 5 second 1~990
1009H	PB Proportional band	0.1 ~ 999.9
100AH	Ti Integral time	0~9,999
100BH	Td Derivative time	0~9,999
100CH	Integration default	0 ~ 100%, unit is 0.1%
100DH	Proportional control offset error	0 ~ 100%, unit is 0.1%
	value, when Ti=0
100EH	The setting of COEF when Dual	0.01 ~99.99, unit is 0.01
	Loop output control are used
100FH	The setting of Dead Band when	-999 ~ 9,999
	Dual Loop output control are
	used
1010H	Hysteresis setting value of the	0~9,999
	1st output group
1011H	Hysteresis setting value of the	0~9,999
	2nd output group
1012H	Output value read and write of	Unit is 0.1%, write operation is valid under manual tuning mode only.
	Output 1
1013H	Output value read and write of	Unit is 0.1%, write operation is valid under manual tuning mode only.
	Output 2
1016H	Temperature regulation value	-99.9 ~ +99.9. Unit is 0.1
1017H	Analog decimal setting	0 ~ 3
101CH	PID parameter selection	0~5/AUTO
101DH	SV value corresponded to PID	Only valid within available range, unit: 0.1 scale
	value
1020H	Alarm 1 type	Please refer to the contents of the “Alarm Outputs” for detail
1021H	Alarm 2 type	Please refer to the contents of the “Alarm Outputs” for detail
1022H	Alarm 3 type	Please refer to the contents of the “Alarm Outputs” for detail
1024H	Upper-limit alarm 1	Please refer to the contents of the “Alarm Outputs” for detail
1025H	Lower-limit alarm 1	Please refer to the contents of the “Alarm Outputs” for detail
1026H	Upper-limit alarm 2	Please refer to the contents of the “Alarm Outputs” for detail
1027H	Lower-limit alarm 2	Please refer to the contents of the “Alarm Outputs” for detail
1028H	Upper-limit alarm 3	Please refer to the contents of the “Alarm Outputs” for detail
1029H	Lower-limit alarm 3	Please refer to the contents of the “Alarm Outputs” for detail
102AH	Read LED Status	b0: ALM3, b1: ALM2, b2: ℉, b3: ℃, b4: ALM1, b5: OUT2, b6:OUT1, b7: AT
102BH	Read Pushbutton Status	b1: F2, b2: Up, b3: Loop, b5: F1, b6: Down, b7: Set, 0: press down key
102CH	Setting lock status
102FH	Software version	V1.00 indicates 0x100
1030H	Start pattern number	0 ~ 15
	Pattern 0~15 temperature set	-999 ~ 9999
1200H~13FFH	point setting (Even number)
	Pattern 0~15 execution time	Time: 0 ~ 900（1 minute per scale）
	setting (Odd number)
1400H~140FH	Actual number of step setting	0 ~ 15 = N, indicate that this pattern is executed from step 0 to step N
	inside the corresponding pattern
	Cycle number for repeating the
1410H~141FH	execution of the correspond	0 ~ 99 indicate that this pattern has been executed for 1 ~ 100 times
	pattern
1420H~142FH	Link pattern number setting of	0 ~ 15, 16 indicates the program end and keep in present step. 17 indicates the
		program end and execution end. 0~15 indicates the next execution pattern
	the correspond pattern
		number after executing the current pattern
Address	Content	Definition
1100H	Adjust Temperature Gain
1101H	Temperature Filter Range	Range of temperature filter: 10~1000, unit: 0.01 ℃, default: 100(1.0℃)
1102H	Temperature Filter Factor	Setting range: 0~50, default: 8

18