Delta DT3 instruction sheet = 1mV, END Stop

SV SLOPE: Set up rising slope (when CRTS = SLOP)
ANALOG OUT1 MAX.: Adjust upper limit compensation for analog Output 1 (1scale = 1μA; 1scale	0
= 1mV)
ANALOG OUT1 MIN.: Adjust lower limit compensation for analog Output 1* (1 scale = 1μA; 1scale	0
= 1mV)
ANALOG OUT2 MAX.: Adjust upper limit compensation for analog Output 2* (1scale = 1μA;	0
1scale = 1mV)
ANALOG OUT2 MIN.: Adjust lower limit compensation for analog Output 2* (1scale = 1μA; 1scale	0
= 1mV)
RETRANSMISSION MAX.: Adjust upper limit compensation for Retransmission* (1scale = 1μA;	0
1scale = 1mV) (display when a Retransmission Card is connected to DT3)
RETRANSMISSION MIN.: Adjust lower limit compensation for Retransmission* (1scale = 1μA;	0
1scale = 1mV) (display when a Retransmission Card is connected to DT3)
REMOTE GAIN: Adjust Remote gain (When CRTS = REMO)	0
REMOTE GAIN: Adjust Remote compensation (When CRTS = REMO)	0
REMOTE LOW: Remote lower limit (When CRTS=REMO)	0
REMOTE HIGH: Remote higher limit (When CRTS=REMO)	100
EVENT1: Set up EVENT1 function (display when a Event Card is connected to EVENT1)	0
EVENT2: Set up EVENT2 function (display when a Event Card is connected to EVENT2)	0
EVENT3: Set up EVENT3 function (display when a Event Card is connected to EVENT3)	0

PID mode: Any of the 6 PID groups can be selected. When set to AUTO mode, the program will automatically select the PID group that is the closest to the target temperature.

Select 0~5 group of PID and execute AT function, the system will automatically load P; I; D and IOF parameters into the selected PID group.

Select the nth PID (n = 0 ~ 5)

press

to set 0 ~ 5th PID parameters

Set up the 0th PID temperature value

~

Set up the 5th PID temperature value

press

V

press

V

Set up the 0th proportional band value

~

Set up the 5th proportional band value

Set up the 0th Ti value

~

Set up the 5th Ti value

Set up the 0th Td value

~

Set up the 5th Td value

Set up the 0th PID integral deviation

~

Set up the 5th PID integral deviation

Press

to set the parameters in

Press

to set the parameters in

“Regulation Mode”

“Regulation Mode”

Programmable Editing: set

to

or

and set

to

.

Select desired editing pattern number 0~F

press

to set the desired editing pattern number 0~F

If the setting is OFF, leave the editing pattern page and go to

to continue with the setting.

Edit the temperature of step No.0 of pattern No. 0

~

Edit the temperature of step No.0 of pattern No. 15

press

V

Edit the time of step No.0 of pattern No. 0 (time unit:

~

Edit the time of step No.0 of pattern No.15 (time unit:

hh, mm)

hh, mm)

~

Set up step 0~15 in order

~

Edit the temperature of step No.15 of pattern No.0

~

Edit the temperature of step No.15 of pattern No.15

Edit the time of step No.15 of pattern No.0

~

Edit the time of step No.15 of pattern No.15

Seelect the actual required steps for executing

~

Seelect the actual required steps for executing

pattern No.0

pattern No.15

Set up the additional cycle (0~199) for pattern No.

~

Set up the additional cycle (0~199) for pattern No.

0 execution

15 execution

Set up the link pattern of pattern No.0 (0~F;

~

Set up the link pattern of pattern No.15 (0~F;

END; STOP)

END; STOP)

Press

to return to the

Press

to return to the

selection of desire editing pattern and number.

selection of desire editing pattern and number

5