ATTACHING THE PINION SHAFT HANDLES

 

 

To reduce the risk of injury, turn unit off

AA

 

and disconnect it from power source before installing

 

 

 

and removing accessories, before adjusting or when

 

 

making repairs. An accidental start-up can cause injury.

 

 

Thread the three pinion shaft handles (AA) in the three

 

 

holes located in the pinion shaft hub (BB) Fig. 14.

 

 

 

BB

AA

ATTACHING THE

 

Fig. 14

LED WORK LIGHT

 

 

To reduce the risk of injury, turn

DD

 

unit off and disconnect it from power source

 

CC

before installing and removing accessories,

CC

 

before adjusting or when making repairs. An

 

 

 

accidental start-up can cause injury.

 

 

The included LED work light is to be attached to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the side of the headstock at wire (CC) Fig. 15.

 

 

 

 

 

 

 

 

 

 

 

 

EE

 

NOTE: Prior to connection, be careful not to

 

 

 

 

 

 

 

 

 

 

 

 

 

 

push wire (CC) into headstock as it is difficult to

 

Fig. 15

 

 

 

 

 

 

Fig. 16

 

 

retrieve.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1. Remove three 6 mm screws (one shown at

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DD) Fig. 15.

 

 

DD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FF

 

 

 

2. Connect the two wires — (CC) from the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FF

 

 

 

 

 

 

 

 

headstock and (EE) from the LED worklight

 

 

 

 

 

 

 

 

 

 

 

 

 

 

— as shown in Fig. 16.

3.Remove plastic cable tie.

4.Push excess wire into the headstock.

5. Attach the LED work light (FF) Fig. 17 to

 

 

 

 

 

 

 

 

Fig. 17

 

 

 

Fig. 18

 

the headstock using three screws removed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

earlier. One is shown at (DD).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6.Final assembly of LED worklight (FF) looks like Figure 18.

GG

CHUCK KEY STORAGE

Storage for your included chuck key (GG) is built into the right side of the drill press head stock. Press chuck key into the holder as shown in Figure 19.

Fig. 19

T-SLOTS

The drill press table is fitted with two T-slots (HH) Fig. 20 for use with various drill press accessories (stop blocks, fences, or clamps). Use 5/16" T-bolts or 1/4-20 hex head bolts when attaching your accessory to the table.

Since accessories other than those offered by DELTA have not been tested with this product, use of such accessories could be hazardous. For safest operation, only DELTA recommended accessories should be used with this product.

HH

Fig. 20

11

Page 11
Image 11
Delta 18-900L, N081935 Attaching the Pinion Shaft Handles, Attaching LED Work Light, Chuck KEY Storage, Slots