Manuals / Desa / Household Appliance / Electric Heater

Desa CRL2718P/N, CRL3124P/N, CGD3018PT/NT damage or personal injury, Continued, Installing Logs

Models: CGD3924PT/NT CGD3018PT/NT CRL3124P/N CRL2718P/N

1 44

Download 44 pages 38.64 Kb

Page 16

INSTALLING LOGS

INSTALLATION

Continued

INSTALLING LOGS

Pin

Back Log (#1)

CAUTION: After installation and periodically thereafter, check to ensure that no flame comes in contact with any log. With the heater set to HI, check to see if flames contact any log. If so, reposition logs according to the log installation instruc- tions in this manual. Flames contacting logs will create soot.

WARNING:Failuretoposition thepartsinaccordancewiththese

Hole in

Grate Base

Burner

Figure 20 - Installing Back Log (#1)

Middle

Log (#2)

Tab

diagrams or failure to use only parts specifically approved with this heater may result in property

Burner

Cutout

damage or personal injury.

Dual Burner Smoky Mountain Oak Models CGD3018PT/NT, CGD3924PT/NT Each log is marked with a number. These num- bers will help you identify the log when install- ing. It is very important to install these logs ex- actly as instructed. Do not modify logs. Only use logs supplied with heater.

1.Locate pins on the bottom of back log (#1). Slide these pins into the holes in the grate base behind the burner (see Figure 20).

2.Place the base of the middle log (#2) in the U- shaped slots of the grate base in front of the back log. The cutout on the right of the middle log should fit over the burner (see Figure 21). Make sure the front of the middle log is resting on the tabs of the grate base and the cutout area is centered over the burner “U” bend.

3.Locate the recesses on the back of the front log (#3). Fit these recesses between the posts of the grate base (see Figure 22).

4.Locate the notches in the bottom of the cross- over log (#4). Place the crossover log on top of the middle log and front log. Make sure the notches of the crossover log lines up with rect- angular knobs on top of the middle and front logs (see Figure 23).

5.Place lava rock around base of heater if de- sired. Do not put lava rock on logs on burner.

“U” Bend

U-Shaped Slot

Figure 21 - Installing Middle Log (#2)

Recess

Front

Log (#3)

Post

Figure 22 - Installing Front Log (#3)

Notches	Crossover
	Log (#4)

Rectangular

Knobs

Figure 23 - Installing Crossover Log (#4)

16

www.desatech.com

111160-01C

Image 16

Desa CRL2718P/N, CRL3124P/N, CGD3018PT/NT, CGD3924PT/NT damage or personal injury, Continued, Installing Logs

Contents

—WHAT TO DO IF YOU SMELL GAS TABLE OF CONTENTS SAFETY INFORMATION PRODUCT IDENTIFICATION SAFETY INFORMATIONContinued PRODUCT FEATURES SAFETY PILOTLOCAL CODES UNPACKINGContinued DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION5.3or applicable local codes ContinuedVENTILATION AIR Figure 3 - Ventilation Air from Inside BuildingINSTALLATION Continued MINIMUM FIREPLACE CLEARANCEWithout Using Hood ContinuedMANTEL CLEARANCES Figure 6 - Heat Resistant Material SlateWhen Using Hood ContinuedFLOOR CLEARANCES Figure 10 - Minimum FireplaceINSTALLING HEATER BASE ASSEMBLY Figure 13 - Attaching Base Assembly to CONNECTING TO GAS SUPPLYFireplace Floor - Dual Burner Model CHECKING GAS CONNECTIONS Continued Figure 17 - Equipment Shutoff ValveFigure 18 - Checking Gas Joints Propane/LP Gas Modelsdamage or personal injury INSTALLING LOGSContinued Figure 25 - Installing Middle Log #2 Figure 26 - Installing Rear Log #3Figure 27 - Installing Crossover Log #4 Figure 24 - Installing Front Log #1Figure 29 - Installing Crossover Log #5 Figure 31 - Installing Crossover Log #7Continued HolesBack Log Post Base Assembly Post Figure 32 - Installing Back LogAssembly Figure 33 - Installing Front LogMANUALLY-CONTROLLED MODELS FOR YOUR SAFETY OPERATING HEATERREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSMANUAL LIGHTING PROCEDURE VARIABLE CONTROL OPERATIONTO TURN OFF GAS TO APPLIANCE Shutting Off HeaterTHERMOSTAT-CONTROLLED MODELS FOR YOUR SAFETY 1.STOP! Read the safety information, col- umnREAD BEFORE LIGHTING LIGHTING INSTRUCTIONSMANUAL LIGHTING PROCEDURE ContinuedTO TURN OFF GAS TO APPLIANCE THERMOSTAT CONTROL OPERATIONPILOT FLAME PATTERN BURNER PRIMARY AIR HOLESMAIN BURNER BURNER INJECTOR HOLDER AND PILOT AIR INLET HOLEContinued LOGSMAIN BURNER Figure 41 - Injector Holder On Outlet Burner TubeTROUBLESHOOTING OBSERVED PROBLEMPOSSIBLE CAUSE REMEDYOBSERVED PROBLEM ContinuedPOSSIBLE CAUSE REMEDYWARNING: If you smell gas •Shut off gas supply Assembly and Thermostat Sensing Bulb FOR MASONRY AND FACTORY- BUILT METAL FIREPLACEFigure 44 - Adhesive-backedMounting Clip Figure 45 - Removing Thermostat Sensing BulbREPLACEMENT PARTS PARTS UNDER WARRANTYPARTS NOT UNDER WARRANTY OPTIONAL POSITIONING OF THERMOSTAT SENSING BULBSPECIFICATIONS DUAL BURNER SMOKY MOUNTAIN OAK MODELSDUAL BURNER BILTMORE SPLIT OAK MODELS SINGLE BURNER SEASONAL OAK MODELSILLUSTRATED PARTS BREAKDOWN PARTS LIST 4 3 20 19 11 13 9 6 21 21 51 2 10 7 14 8 15 21 16 19 17 21103008-02 22 1420 24 21 13 15 11 8 23 23 3 12 6 9 16 10 17 23 1821 23 111160-01C111340-03 111160-01C Peg positions vary according to model 2 522 1420 24 21 13 15 11 8 23 23 9 7 12 6 25 16 10 17 23 18111340-02 111160-01C VARIABLE MANUALLY-CONTROLLEDSEASONAL OAK MODELS PARTS CENTRAL Portable Heater PartsMaster Parts Dist Washer Equipment CoEQUIPMENT SHUTOFF VALVE - GA5010 INFORMATION VIDEO -FIREPLACE HOOD DAMPER CLAMP - GA6080 Not ShownKEEP THIS WARRANTY LIMITED WARRANTYModel ____________________________ Serial No. _________________________