Register Definitions, Base + Read | Diamond Power Products MM-48-AT

6. REGISTER DEFINITIONS

Base + 0	Write		D/A LSB

Bit No.	7	6		5	4	3	2	1	0

Name	DA7	DA6		DA5	DA4	DA3	DA2	DA1	DA0

Definitions:

DA7-0 D/A bits 7-0; DA0 is the LSB. D/A data is an unsigned 12-bit number ranging from 0 to 4095.

Base + 0	Read		A/D LSB

Bit No.	7	6		5	4	3	2	1	0

Name	AD7	AD6		AD5	AD4	AD3	AD2	AD1	AD0

Definitions:

AD7 – 0 A/D LSB data (bits 7-0 of the 16-bit value). A/D data is a signed 16-bit value ranging from -32768 to 32767.

Base + 1	Write		DAC 0 – 3 MSB

Bit No.	7	6		5	4	3	2	1	0

Name						DA11	DA10	DA9	DA8

Definitions:

DA11 – 8 D/A data bits 11-8 for the selected channel. DA11 is the MSB.

Diamond-MM-48-AT User Manual V1.01

Page 11

Image 11

Diamond Power Products MM-48-AT user manual Register Definitions, Base + Read, Base + Write DAC 0 3 MSB

Contents

DIAMOND-MM-48-AT Table of Contents Description DIAMOND-MM-48-AT Board Drawing J3 Analog and Digital I/O Signal Name DefinitionO Header Pinout and PIN Description Optoisolated input contacts Signal Name Definition Relay output contactsJ4 Relays and Optocouplers Interrupt Level Selection Board ConfigurationBase Address Base Address Jumper Position Hex Decimal Analog Input Range Optocoupler PolarityReserved LSB MSB OverviewBase + Write Function Read Function Read operations Register Map Bit AssignmentsWrite operations DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Base + Read Register DefinitionsBase + Write Definitions HIGH3 HIGH2 HIGH1 HIGH0 LOW3 LOW2 LOW1 LOW0 AD9 AD8Base + Read/Write A/D Channel Register DIR3 DIR2 DIR1 DIR0 Base + Read/Write Digital I/O Configuration RegisterBase + Read/Write Relay Control Port RELAY7 RELAY6 RELAY5 RELAY4 RELAY3 RELAY2 RELAY1 RELAY0 OEN3 OEN2 OEN1 OEN0 POL3 POL2 POL1 POL0 DIO3 DIO2 DIO1 DIO0Base + Read Digital I/O Data and Edge Status DEDGE3 DEDGE2 DEDGE1 DEDGE0 DIO3 DIO2 DIO1 DIO0 OEDGE3 OEDGE2 OEDGE1 OEDGE0 OPTO3 OPTO2 OPTO1 OPTO0 Base + Write Channel and Control RegisterDaupdt DACH2 DACH1 DACH0 Dapre Daprld Reset Fiforst Adstart Base + Write Command Register POL ADCH3 ADCH2 ADCH1 ADCH0 Base + Read Status Register CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Write Configuration Register Adbusy Dabusy CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Read Configuration & Status Register OVF Fifoth Fifoen Scanen Base + Write Fifo Control RegisterFifoth Fifoen Scanen Base + Read Fifo Status Register Clrt Clrd Clro Clra Tinte Dinte Ointe Ainte Base + Write Interrupt Control Register Tint Dint Oint Aint Tinte Dinte Ointe Ainte Base + Read Interrupt Status Register Base + Read/Write Counter/Timer D23 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D15 Ctrno Base + Write Counter/Timer Control RegisterCtrno Latch Gtdis Gten Ctdis Cten Load CLR Base + Read/Write Eeprom / TrimDAC Address Register Base + Read/Write Eeprom / TrimDAC Data Register Base + Read Fpga Revision Code Base + Write Eeprom Access Key RegisterBase + Write Calibration Control Register Base + Read Calibration Status Register Single Ended and Differential Inputs Analog Input Ranges and ResolutionResolution Input Ranges Performing AN A/D Conversion LSB = readbase MSB = readbase+1 Data = MSB * 256 + LSB Trigger an A/D conversion on the current channel Input voltage = A/D value / 32768 * Full-scale voltage Conversion or Scan D SCAN, FIFO, and Interrupt OperationTrigger Clken Clksel Fifoen = Fifo OperationInterrupt Operation Fifoen Fifoth Scanen Ainte Fifoen Scanen Guidelines for Selecting Fifo Use Fifoen and FifothOperation Table Analog Output Overview Generating AN Analog Output 12.3 D/A Calibration Autocalibration OperationReference Voltages 12.2 A/D calibration Digital I/O Operation Optocoupler Operation Procedure for enabling interrupts on selected edges Polarity and logic readback Edge detection assumes OENn = 1 to enable edge detection Relay Operation Counter 1 Counting/Totalizing Functions COUNTER/TIMER OperationCounter 0 A/D Sample Control Counter Command Sequences Counter Outpbase+15,0x01 Outpbase+15,0x81 General SpecificationsAutocalibration

Diamond Power Products MM-48-AT user manual Register Definitions, Base + Write, Base + Read

Models: MM-48-AT

6. REGISTER DEFINITIONS

Base + 0

Write

D/A LSB

DA7

Definitions:

Base + 0

Read

AD7

Base + 1

Write

DAC 0 – 3 MSB