Manuals / Diamond Power Products / Computer Equipment / Network Card

Diamond Power Products user manual DIAMOND-MM-48-AT Board Drawing

Models: MM-48-AT

1 44

Download 44 pages 15.07 Kb

Page 4

2. DIAMOND-MM-48-AT BOARD DRAWING

Feature descriptions

J1 PC/104 8-bit bus connector

J2 PC/104 16-bit bus connector

J3 Analog and digital I/O connector

J4 Relay and optocoupler I/O connector

J6 Configuration jumper block

J7 Factory use only (used in factory calibration process)

J10 +/-5 input range selection (bipolar model only)

Diamond-MM-48-AT User Manual V1.01

Page 4

Image 4

Diamond Power Products user manual DIAMOND-MM-48-AT Board Drawing

Contents

DIAMOND-MM-48-AT Table of Contents Description DIAMOND-MM-48-AT Board Drawing O Header Pinout and PIN Description Signal Name DefinitionJ3 Analog and Digital I/O J4 Relays and Optocouplers Signal Name Definition Relay output contactsOptoisolated input contacts Board Configuration Base AddressBase Address Jumper Position Hex Decimal Interrupt Level SelectionReserved Optocoupler PolarityAnalog Input Range Base + Write Function Read Function OverviewLSB MSB Register Map Bit Assignments Write operationsDA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Read operationsRegister Definitions Base + WriteDefinitions Base + ReadBase + Read/Write A/D Channel Register AD9 AD8HIGH3 HIGH2 HIGH1 HIGH0 LOW3 LOW2 LOW1 LOW0 Base + Read/Write Digital I/O Configuration Register Base + Read/Write Relay Control PortRELAY7 RELAY6 RELAY5 RELAY4 RELAY3 RELAY2 RELAY1 RELAY0 DIR3 DIR2 DIR1 DIR0DIO3 DIO2 DIO1 DIO0 Base + Read Digital I/O Data and Edge StatusDEDGE3 DEDGE2 DEDGE1 DEDGE0 DIO3 DIO2 DIO1 DIO0 OEN3 OEN2 OEN1 OEN0 POL3 POL2 POL1 POL0Daupdt DACH2 DACH1 DACH0 Base + Write Channel and Control RegisterOEDGE3 OEDGE2 OEDGE1 OEDGE0 OPTO3 OPTO2 OPTO1 OPTO0 Base + Write Command Register Dapre Daprld Reset Fiforst AdstartBase + Read Status Register POL ADCH3 ADCH2 ADCH1 ADCH0Base + Write Configuration Register CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken ClkselBase + Read Configuration & Status Register Adbusy Dabusy CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken ClkselBase + Write Fifo Control Register Fifoth Fifoen ScanenBase + Read Fifo Status Register OVF Fifoth Fifoen ScanenBase + Write Interrupt Control Register Clrt Clrd Clro Clra Tinte Dinte Ointe AinteBase + Read Interrupt Status Register Tint Dint Oint Aint Tinte Dinte Ointe AinteBase + Read/Write Counter/Timer D15 Base + Read/Write Counter/Timer D7Base + Read/Write Counter/Timer D23 Ctrno Latch Gtdis Gten Ctdis Cten Load CLR Base + Write Counter/Timer Control RegisterCtrno Base + Read/Write Eeprom / TrimDAC Data Register Base + Read/Write Eeprom / TrimDAC Address RegisterBase + Write Eeprom Access Key Register Base + Write Calibration Control RegisterBase + Read Calibration Status Register Base + Read Fpga Revision CodeAnalog Input Ranges and Resolution ResolutionInput Ranges Single Ended and Differential InputsPerforming AN A/D Conversion Trigger an A/D conversion on the current channel LSB = readbase MSB = readbase+1 Data = MSB * 256 + LSBInput voltage = A/D value / 32768 * Full-scale voltage D SCAN, FIFO, and Interrupt Operation TriggerClken Clksel Conversion or ScanFifo Operation Interrupt OperationFifoen Fifoth Scanen Fifoen =Operation Table Guidelines for Selecting Fifo Use Fifoen and FifothAinte Fifoen Scanen Analog Output Overview Generating AN Analog Output Autocalibration Operation Reference Voltages12.2 A/D calibration 12.3 D/A CalibrationDigital I/O Operation Procedure for enabling interrupts on selected edges Optocoupler OperationEdge detection assumes OENn = 1 to enable edge detection Polarity and logic readbackRelay Operation Counter 0 A/D Sample Control COUNTER/TIMER OperationCounter 1 Counting/Totalizing Functions Command Sequences CounterCounter Outpbase+15,0x01 Outpbase+15,0x81 Autocalibration SpecificationsGeneral