Diamond Power Products MM-48-AT specs

Base + 9

Write

Configuration Register

Bit No.

7

6

5

4

3

2

1

0

Name

CKSEL1

CKFRQ1

CKFRQ0

SCNINT

CLKEN

CLKSEL

CKSEL1

Clock source select for counter/timer 1:

1

External signal Clk0 in I/O connector J3

0

On-board clock, frequency selected by CKFRQ1 below

CKFRQ1

Clock frequency select for counter/timer 1 when CKSEL1 = 0:

1

100KHz

0

10MHz

CKFRQ0

Clock frequency select for counter/timer 0:

1

1MHz

0

10MHz

SCNINT

Scan interval. This is the time between A/D samples during an A/D scan. An A/D

scan occurs when SCANEN = 1 (Base + 10 bit 4) and an A/D conversion is

triggered.

1

5.0µS

0

9.3µS

CLKEN

Enable hardware A/D clock:

1

Enable hardware A/D trigger (source is selected with CLKSEL bit); software

triggers are disabled

0

Disable hardware trigger; A/D is triggered by setting the ADSTART bit

CLKSEL

A/D clock select, used only when CLKEN = 1:

1

Internal clock: counter/timer 0 generates A/D conversions

0

External clock: the EXTCLK pin on I/O connector J3, generates A/D

conversions

Diamond-MM-48-AT User Manual V1.01

Page 18

Image 18

Diamond Power Products MM-48-AT user manual Base + Write Configuration Register, CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel

Contents

DIAMOND-MM-48-AT Table of Contents Description DIAMOND-MM-48-AT Board Drawing Signal Name Definition O Header Pinout and PIN DescriptionJ3 Analog and Digital I/O Signal Name Definition Relay output contacts J4 Relays and OptocouplersOptoisolated input contacts Base Address Jumper Position Hex Decimal Board ConfigurationBase Address Interrupt Level Selection Optocoupler Polarity ReservedAnalog Input Range Overview Base + Write Function Read FunctionLSB MSB DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 Register Map Bit AssignmentsWrite operations Read operations Definitions Register DefinitionsBase + Write Base + Read AD9 AD8 Base + Read/Write A/D Channel RegisterHIGH3 HIGH2 HIGH1 HIGH0 LOW3 LOW2 LOW1 LOW0 RELAY7 RELAY6 RELAY5 RELAY4 RELAY3 RELAY2 RELAY1 RELAY0 Base + Read/Write Digital I/O Configuration RegisterBase + Read/Write Relay Control Port DIR3 DIR2 DIR1 DIR0 DEDGE3 DEDGE2 DEDGE1 DEDGE0 DIO3 DIO2 DIO1 DIO0 DIO3 DIO2 DIO1 DIO0Base + Read Digital I/O Data and Edge Status OEN3 OEN2 OEN1 OEN0 POL3 POL2 POL1 POL0 Base + Write Channel and Control Register Daupdt DACH2 DACH1 DACH0OEDGE3 OEDGE2 OEDGE1 OEDGE0 OPTO3 OPTO2 OPTO1 OPTO0 Base + Write Command Register Dapre Daprld Reset Fiforst Adstart Base + Read Status Register POL ADCH3 ADCH2 ADCH1 ADCH0 Base + Write Configuration Register CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Read Configuration & Status Register Adbusy Dabusy CKSEL1 CKFRQ1 CKFRQ0 Scnint Clken Clksel Base + Read Fifo Status Register Base + Write Fifo Control RegisterFifoth Fifoen Scanen OVF Fifoth Fifoen Scanen Base + Write Interrupt Control Register Clrt Clrd Clro Clra Tinte Dinte Ointe Ainte Base + Read Interrupt Status Register Tint Dint Oint Aint Tinte Dinte Ointe Ainte Base + Read/Write Counter/Timer D7 Base + Read/Write Counter/Timer D15Base + Read/Write Counter/Timer D23 Base + Write Counter/Timer Control Register Ctrno Latch Gtdis Gten Ctdis Cten Load CLRCtrno Base + Read/Write Eeprom / TrimDAC Data Register Base + Read/Write Eeprom / TrimDAC Address Register Base + Read Calibration Status Register Base + Write Eeprom Access Key RegisterBase + Write Calibration Control Register Base + Read Fpga Revision Code Input Ranges Analog Input Ranges and ResolutionResolution Single Ended and Differential Inputs Performing AN A/D Conversion Trigger an A/D conversion on the current channel LSB = readbase MSB = readbase+1 Data = MSB * 256 + LSB Input voltage = A/D value / 32768 * Full-scale voltage Clken Clksel D SCAN, FIFO, and Interrupt OperationTrigger Conversion or Scan Fifoen Fifoth Scanen Fifo OperationInterrupt Operation Fifoen = Guidelines for Selecting Fifo Use Fifoen and Fifoth Operation TableAinte Fifoen Scanen Analog Output Overview Generating AN Analog Output 12.2 A/D calibration Autocalibration OperationReference Voltages 12.3 D/A Calibration Digital I/O Operation Procedure for enabling interrupts on selected edges Optocoupler Operation Edge detection assumes OENn = 1 to enable edge detection Polarity and logic readback Relay Operation COUNTER/TIMER Operation Counter 0 A/D Sample ControlCounter 1 Counting/Totalizing Functions Command Sequences Counter Counter Outpbase+15,0x01 Outpbase+15,0x81 Specifications AutocalibrationGeneral