Manuals / Emerson / Computer Equipment / Computer Hardware

Emerson MVME7100 manual Operation, Installation

Models: MVME7100

1 106

Download 106 pages 17.7 Kb

Page 19

Operation

Safety Notes

Operation

Product Damage

High humidity and condensation on the board surface causes short circuits. Do not operate the board outside the specified environmental limits.

Make sure the board is completely dry and there is no moisture on any surface before applying power.

Damage of Circuits

Electrostatic discharge and incorrect installation and removal can damage circuits or shorten their life.

Before touching the board or electronic components, make sure that you are working in an ESD-safe environment.

Board Malfunction

Switches marked as “reserved” might carry production-related functions and can cause the board to malfunction if their setting is changed.

Do not change settings of switches marked as “reserved”. The setting of switches which are not marked as “reserved” has to be checked and changed before board installation.

Installation

Data Loss

Powering down or removing a board before the operating system or other software running on the board has been properly shut down may cause corruption of data or file systems.

Make sure all software is completely shut down before removing power from the board or removing the board from the chassis.

Product Damage

Only use injector handles for board insertion to avoid damage to the front panel and/or PCB. Deformation of the front panel can cause an electrical short or other board malfunction.

Product Damage

Inserting or removing modules with power applied may result in damage to module components.

Before installing or removing additional devices or modules, read the documentation that came with the product.

MVME7100 Single Board Computer Installation and Use (6806800E08A)

19

Image 19

Emerson MVME7100 manual Operation, Installation

Contents

November 6806800E08AInstallation and Use MVME7100 Single Board ComputerLimited and Restricted Rights Legend TrademarksContact Address About this Manual Safety Notes Sicherheitshinweise 1 Introduction Contents2 Hardware Preparation and Installation 4 Functional Description 3 Controls, LEDs, and Connectors5 Transition Module A Battery Exchange6 MOTLoad Firmware B Related Documentation ContentsRelated Specifications MVME7100 Single Board Computer Installation and Use 6806800E08ATable B-1 List of TablesEmerson Network Power - Embedded Computing Publications MVME7100 Single Board Computer Installation and Use 6806800E08AList of Tables MVME7100 Single Board Computer Installation and Use 6806800E08AFigure A-1 List of FiguresMVME7100 Single Board Computer Installation and Use 6806800E08A Secondary Side Thermally Significant ComponentsList of Figures MVME7100 Single Board Computer Installation and Use 6806800E08AAbout this Manual Overview of ContentsTERM AbbreviationsMVME7100 Single Board Computer Installation and Use 6806800E08A About this ManualMEANING MVME7100 Single Board Computer Installation and Use 6806800E08AAbout this Manual TERMMEANING MVME7100 Single Board Computer Installation and Use 6806800E08AAbout this Manual TERMNotation ConventionsMVME7100 Single Board Computer Installation and Use 6806800E08A About this ManualComments and Suggestions Summary of ChangesSafety Notes MVME7100 Single Board Computer Installation and Use 6806800E08A Safety NotesOperation InstallationBattery Cabling and ConnectorsSicherheitshinweise Betrieb Installation Kabel und SteckerUmweltschutz BatterieFeatures 1.1 FeaturesIntroduction Table 1-1 Features ListMVME7100 Single Board Computer Installation and Use 6806800E08A Table 1-1 Features List continuedIntroductionFeatures FeaturesMVME7100 Single Board Computer Installation and Use 6806800E08A 1.2 Standard Compliances1.3 Mechanical Data CharacteristicTable 1-4 Board Variants 1.4.2 Board Accessories1.4 Ordering Information 1.4.1 Supported Board Models2.1 Overview Hardware Preparation and InstallationTable 2-1 Startup Overview Shipment Inspection 2.2 Unpacking and Inspecting the Board2.3.1 Environmental Requirements 2.3 RequirementsTable 2-2 MVME7100 Specifications Table 2-3 Power Requirements 2.3.2 Power Requirements2.3.4 Thermally Significant Components 2.3.3 Thermal RequirementsTable 2-4 Thermally Significant Components Figure 2-2 Secondary Side Thermally Significant Components Hardware Preparation and InstallationMVME7100 Single Board Computer Installation and Use 6806800E08A Figure 2-1 Primary Side Thermally Significant ComponentsMVME7100 Single Board Computer Installation and Use 6806800E08A 2.3.5 Equipment Requirementsz Transition module and connecting cables Hardware Preparation and InstallationS1 S2 2.4 Configuring the BoardFigure 2-3 Switch Locations Figure 2-4 SMT Configuration Switch Position 2.4.1 SMT Configuration Switch, S1Table 2-5 Configuration Switch Settings S1 2.4.1.4 JTAG Pass-Thru 2.4.1.1 Safe Start Switch2.4.1.2 Boot Block B Select 2.4.1.3 Flash Bank Write ProtectFigure 2-5 Geographical Address Switch Position 2.4.2 Geographical Address Switch, S22.4.3 VME System Controller Select, S2 2.4.1.7 Master WP2.5.1 Transition Module 2.5 Installing AccessoriesTable 2-6 VME System Controller and GA Switch Settings continued 2.5.2 PMC Installation and Removal ProcedureInstallation Procedure 2.5.3 XMCspan 2.6 Installing and Removing the BoardFigure 2-6 Typical Placement of a PMC Module on a VME Module 2. Remove any filler panel that might fill that slot Installation and Removal Procedure2.8 Factory Installed Linux 2.7 Completing the InstallationMVME7100 bmw -af8000000 -bf8f00000 -c4000000 MVME7100 execP -l4000400 Login as root Battery J3 J2 J4A/J4B Controls, LEDs, and Connectors3.1 Overview 3.2 Board Layout3.3 Front Panel 3.3.1 Reset/Abort SwitchFigure 3-2 Front Panel LEDs, Connectors, Switch Table 3-1 Front Panel LEDs 3.3.2 LEDsControls, LEDs, and Connectors MVME7100 Single Board Computer Installation and Use 6806800E08ATable 3-2 Baseboard Connectors 3.3.3 ConnectorsControls, LEDs, and Connectors 3.3.3.1 XMC Expansion Connector J6Table 3-3 XMC Expansion Connector J6 Pin Assignments ConnectorsTable 3-3 XMC Expansion Connector J6 Pin Assignments continued 3.3.3.2 Ethernet Connectors J4A/J4BTable 3-4 Ethernet Connectors J4A/J4B Pin Assignments Table 3-4 Ethernet Connectors J4A/J4B Pin Assignments continued 3.3.3.3 PCI Mezzanine Card PMC Connectors J11 - J14, J21 - J23Table 3-5 PMC Slot 1 Connector J11 Pin Assignments Signal Table 3-5 PMC Slot 1 Connector J11 Pin Assignments continuedTable 3-6 PMC Slot 1 Connector J12 Pin Assignments Controls, LEDs, and ConnectorsConnectorsSignal Table 3-6 PMC Slot 1 Connector J12 Pin Assignments continuedTable 3-7 PMC Slot 1 Connector J13 Pin Assignments ConnectorsControls, LEDs, and ConnectorsSignal Table 3-7 PMC Slot 1 Connector J13 Pin Assignments continuedTable 3-8 PMC Slot 1 Connector J14 Pin Assignments Controls, LEDs, and ConnectorsConnectorsSignal Table 3-8 PMC Slot 1 Connector J14 Pin Assignments continuedTable 3-9 PMC Slot 2 Connector J21 Pin Assignments ConnectorsControls, LEDs, and ConnectorsSignal Table 3-9 PMC Slot 2 Connector J21 Pin Assignments continuedTable 3-10 PMC Slot 2 Connector J22 Pin Assignments Controls, LEDs, and ConnectorsConnectorsSignal Table 3-10 PMC Slot 2 Connector J22 Pin Assignments continuedTable 3-11 PMC Slot 2 Connector J23 Pin Assignments ConnectorsControls, LEDs, and ConnectorsTable 3-12 COM1 Port Connector Pin Assignments 3.3.3.4 Serial Port Connector COM1/J13.3.3.5 VMEbus P1 Connector Table 3-11 PMC Slot 2 Connector J23 Pin Assignments continuedConnectorsControls, LEDs, and Connectors 3.3.3.6 VMEbus P2 ConnectorTable 3-13 VMEbus P1 Connector Pin Assignments continued Table 3-14 VME P2 Connector PinoutsP2-Z Table 3-14 VME P2 Connector Pinouts continuedControls, LEDs, and ConnectorsConnectors MVME7100 Single Board Computer Installation and Use 6806800E08ATable 3-15 MVME721 Host I/O Connector J10 Pin Assignments 3.3.3.7 MVME7216E PMC I/O Module PIM Connectors J10, J14Table 3-15 MVME721 Host I/O Connector J10 Pin Assignments continued 3.3.3.8 USB Connector J23.4 Headers 3.4.1 Processor COP Header P4Table 3-18 Boundary Scan Header P5 Pin Assignments 3.4.2 Boundary Scan Header P5MVME7100 Single Board Computer Installation and Use 6806800E08A Controls, LEDs, and ConnectorsBoundary Scan Header P5 4.1 Overview Functional Description4.3 Processor 4.2 Block DiagramFigure 4-1 Block Diagram 4.5 System Memory 4.4 I2C Serial Interface and DevicesTimers 4.6 Timers4.7 Ethernet Interfaces 4.8 Local Bus Interface4.8.3 Quad UART QUART 4.8.4 Control and Timers PLD4.8.1 Flash Memory 4.8.2 NVRAM4.10.2 USB 4.9 DUART Interface4.10 PCI-E Port 4.10.1 VME Controller4.12.3 Power Supply Filtering and Fusing 4.12 Power Supplies4.12.1 Power Sequencing 4.12.2 Power Supply Monitor4.13.2 Real Time Clock Input 4.14 Reset Control Logic4.15 Real Time Clock Battery 4.13.1 System ClockFigure 5-1 Component Layout Transition Module5.1 Overview 5.2 Transition Module LayoutFigure 5-2 Block Diagram 5.3 Features5.4 SEEPROM Address Switch, S1 Table 5-1 Transition Module FeaturesTable 5-4 Transition Module Connectors 5.5 Rear Panel ConnectorsTable 5-2 SEEPROM Address Switch Assignments RTM Table 5-3 Switch Settings and Device AddressesTable 5-5 Transition Module LEDs Figure 5-4 Rear Panel Connectors and LEDsRear Panel Connectors MVME7100 Single Board Computer Installation and Use 6806800E08A5.6 PMC Input/Output Module ProcedurePMC Input/Output Module Figure 5-5 Installing the PIMMVME7100 Single Board Computer Installation and Use 6806800E08A Transition Module6.2 Implementation and Memory Requirements 6.3 MOTLoad CommandsMOTLoad Firmware 6.1 OverviewTests 6.3.2 TestsCommand 6.3.3 Command ListTable 6-1 MOTLoad Commands Command ListMVME7100 Single Board Computer Installation and Use 6806800E08A Table 6-1 MOTLoad Commands continuedMOTLoad FirmwareCommand List CommandMVME7100 Single Board Computer Installation and Use 6806800E08A Table 6-1 MOTLoad Commands continuedCommand ListMOTLoad Firmware CommandCommand 6.4 Using the Command Line InterfaceTable 6-1 MOTLoad Commands continued MOTLoad FirmwareUsing the Command Line InterfaceExample MVME7100 flashProgram -d/dev/flash0 -n00100000 6.4.1 Rules6.4.2 Help help commandnamez MVME7100 vmeCfg -s -r234 6.5 Firmware Settings6.5.1 Default VME Settings z MVME7100 vmeCfg -s -mz MVME7100 vmeCfg -s -o1 z MVME7100 vmeCfg -sz MVME7100 vmeCfg -s -o2 z MVME7100 vmeCfg -s -o7 z MVME7100 vmeCfg -s -o36.5.3 Displaying VME Settings 6.5.2 Control Register/Control Status Register Settings6.5.4 Editing VME Settings vmeCfg -z 6.5.5 Deleting VME Settings6.5.6 Restoring Default VME Settings 6.6 Remote Start6.7 Boot Images 6.7.2 Image Flags 6.7.1 Checksum AlgorithmTable 6-2 MOTLoad Image Flags 6.7.3 User Images 6.7.5 Alternate Boot Images and Safe Start 6.7.4 Alternate Boot Data Structure6.7.6 Boot Image Firmware Scan 6.8 Startup Sequence Figure A-1 Battery Location Battery ExchangeA.1 Battery Exchange Battery1. Remove the old battery Exchange Procedure2. Install the new battery with the plus sign + facing up Table B-1 Emerson Network Power - Embedded Computing Publications B.1 Emerson Network Power - Embedded Computing DocumentsRelated Documentation B.2 Manufacturers’ DocumentsDocument Title and Source MVME7100 Single Board Computer Installation and Use 6806800E08ATable B-2 Manufacturer’s Publications continued Related DocumentationManufacturers’ DocumentsMVME7100 Single Board Computer Installation and Use 6806800E08A B.3 Related SpecificationsTable B-3 Related Specifications Related SpecificationsRelated DocumentationOrganization and Standard Table B-3 Related Specifications continuedRelated DocumentationRelated Specifications MVME7100 Single Board Computer Installation and Use 6806800E08AIndex MVME7100 Single Board Computer Installation and Use 6806800E08A