RF STANDING PILOT OPERATING INSTRUCTIONS

Features

Benefits

• Self powered millivolt receiver/valve

• No external power or batteries required to operate valve and flame modulation

• Thermostat performance

• Flame cycles and modulates such that heat output equals heat loss from the room

• Auto mode

• Flame & fan are controlled automatically

• Self powered millivolt control

• No external power required to control gas valve and flame modulation

• Integrated Valve Electronics

• No electronics, rheostat, or limit installation required

• Failure analysis

• Troubleshooting with information from LED

• Pilotstat interlock

• When valve is turned off, power unit must drop out before pilot can be relit

• F or C temperature units

• Display local temperature units

Please review and retain the instructions included with the RF Transmitter. It provides additional information and details concerning the operational procedures and functions for the RF Remote Control.

Functions

Flame powered system

Flame powered flame modulation

Electronics integrated into valve to provide thermostat, flame, and fan functions with RF commands

Temperature compensated RF receiver

Main burner goes to "high" when manual switch is set on "local"

Fan powered by 120 vac

Transmitter Signal

When the transmitter is in the Auto mode, a signal is sent every 10 minutes if there is a change in the room temperature

When the transmitter is in the On or Off modes, a signal is also sent every 10 minutes with the status of On or Off condition

The transmitter will work at a minimum of 25 feet from the receiver

Make sure antennae is not touching metal and is horizontal.

Receiver Shutdown of Burner

In the remote, auto mode the valve shuts off if it does not receive a signal within 3 hours from the transmitter

In the local mode the valve does not shut off

In the remote, manual mode the valve shuts off if it does not receive a signal within 6 hours from the transmitter

Thermopiles

The negative leads (white) must be connected to the terminals with the one white dot marked next to them

Each thermopile must provide at least 500 mV open circuit voltage

If output is erratic, check thermopile for intermittent shorts

LED Troubleshooting

Note: In normal operation, LED blinks once every two seconds; also, LED will be on for one second after every valid command received by the RV8310D; these are not error codes.

Failure codes (see Table) can occur anytime after the pilot burner is lit. Failure code timing is 1/4 second on, 1/2 second off.

Sequence is failure code followed by LED not blinking for four seconds.

In the event of multiple failure codes, the next failure code follows the previous failure code by approximately three seconds.

Code

Service Action

8

Replace valve

7Confirm stepper motor connection exists

4Fuel conversion plug missing or has poor connection (RV8310E only)

3Replace thermopile with Q313

2Device too hot. Check application

1None required. This is normal operation and indicates the control is powered

Page 56

25613-0-0309

Page 56
Image 56
Empire Comfort Systems DVX36DP31(N,P)-1, DVX36DP91(N,P)-1, DVX36DP71(N,P)-1 RF Standing Pilot Operating Instructions

DVX42DP71(N,P)-1, DVX36DP31(N,P)-1, DVX42DP91(N,P)-1, DVX42DP31(N,P)-1, DVX36DP71(N,P)-1 specifications

Empire Comfort Systems has long been a trusted name in heating solutions, and their line of direct vent gas fireplaces showcases a blend of innovation, style, and efficiency. Among their standout models are the DVX36DP91(N,P)-1, DVX36DP71(N,P)-1, DVX42DP31(N,P)-1, DVX42DP91(N,P)-1, and DVX36DP31(N,P)-1. Each of these models boasts unique features and technologies, making them ideal choices for modern living spaces.

One of the defining characteristics of these fireplaces is their direct vent system, which allows for safe and efficient venting of combustion gases. By drawing air from the outside, these models maintain indoor air quality and eliminate the need for a traditional chimney. This is particularly beneficial in homes where space is limited or where aesthetic considerations make a chimney impractical.

The DVX series is designed with user convenience in mind. Many models come equipped with a remote control, allowing homeowners to adjust settings such as flame height and heat output from the comfort of their favorite chair. The ability to customize the ambiance is enhanced by the inclusion of realistic ceramic logs and glowing embers, creating a warm and inviting atmosphere.

Efficiency is a key feature of the Empire Comfort Systems DVX series. These fireplaces are designed to maximize heat output while minimizing energy consumption. With high-efficiency ratings, they provide warmth without significantly impacting utility bills. Additionally, the models are available in both natural gas and propane variants, catering to different preferences and availability.

In terms of design, the DVX series offers versatile options that can seamlessly integrate with various home decors. With customizable fronts, finishes, and media choices, owners can match their fireplace to their home’s aesthetic, whether it be modern, traditional, or somewhere in between.

Maintenance is simplified, thanks to the easy-access features that allow for quick cleaning and servicing. The durable construction ensures long-lasting performance, making these fireplaces a worthwhile investment.

With their focus on efficiency, style, and advanced technology, Empire Comfort Systems’ DVX36DP91(N,P)-1, DVX36DP71(N,P)-1, DVX42DP31(N,P)-1, DVX42DP91(N,P)-1, and DVX36DP31(N,P)-1 models represent some of the best options available for homeowners seeking a reliable and attractive heating solution.