Manuals / Enviro / Household Appliance / Home Security System

Enviro EA800 owner manual Operation

Models: EA800

1 98

Download 98 pages 50.46 Kb

Page 4

Operation

Operation	49
Monitoring Environmental Conditions	49
Viewing Sensor Settings	50
Viewing Active Alarms	50
Viewing the Alarm Log	51
Viewing Pending Alarm Information	51
Viewing Limit Settings	52
Viewing the Event Log	52
Viewing the Sensor Log	53
Viewing Firmware Information	53
Viewing RF Information	54
Maintenance	55
Locking and Unlocking the EA800	55
Pausing Monitoring and Cancelling Pause	56
Adding a Sensor	57
Replacing a Sensor	57
Editing Sensor Parameters	58
Reprogramming a Relay	59
Deleting a Sensor	59
Changing the Date Format	60
Changing the Time Format	60
Changing the Date or Time Setting	61
Changing Sensor Data Collection Frequency	61
Changing the Buzzer Setting	62
Changing the Password	63
Clearing the Alarm Log	64
Clearing the Sensor Log	64
Updating the Firmware	65
Saving Configuration Settings	66
Loading Configuration Settings	67
Exporting the Stored Logs	68
Exported Alarm Data	68
Exported Event Data	69
Exported Sensor Data	69
Troubleshooting	71
Verifying RF Signal Strength	72
Viewing Signal Strength for a Wireless Sensor	72
Specifications	73
Base Unit and Sensor Specifications	73
Accessories	74
Appendix A: Screen Maps	75
Appendix B: Planning Worksheet	83
Appendix C: Wiring Diagram	85
Appendix D: System Configuration Record	87
Warranty and Service Information	93

ii	D-011-0152

Image 4

Enviro EA800 owner manual Operation

Contents

D-011-0152 Limitations of the Alarm System or Device Table of Contents InstallationGeneral Information PreparationOperation General Information OverviewHow to Use This Manual General Information Block DiagramsD-011-0152 Symbols on the Product or Manual Labeling General Information Monitoring ScreensD-011-0152 Keys Base Unit Connections Access Control and Passwords will sound when an alarm occurs if DISABLE is System Configuration Parametersselected Temperature Sensors Sensors4-20mASensors Humidity SensorsTheory of Operation Power Supply / Sensor Voltage Selection Multi-FunctionSensors Water SensorsContact Closure Sensors Sensor Parameter Descriptions ResolutionMaximum Allowed High Scaled ValueRelay Operation Relay Operation D-011-0152Preparation D-011-0152 From 11-26VDC power supply To alarm-on-closedloop circuit power supplied via loop From 11-26VDC power supplyD-011-0152 Installation Power RequirementsTools and Supplies Required Mounting the EA800 Rear PlateEA800 Base Unit Power Connections Install the Wired SensorsInstall the Wireless Sensors RESET BUTTON SENSOR MODEL NORESET BUTTON SENSOR MODEL NOD-011-0152 J6 Input 1 Input 2 Input 3 InputConnecting Wired HA-III+Humidity Sensors Connecting Wired 4-20mASensors Connecting the EA800 Alarm Outputs ProgrammingAccessing the MAIN MENU for Programming Configuring System Parameter Settings3.Enter the SYSTEM menu and then select the CONFIGURATION menu as shown below DISABLED is selected Setting the Current Date Setting the Time D-011-0152Adding Wireless Sensors Adding a Wireless Temperature SensorAdding Wireless Sensors D-011-0152Installation D-011-0152D-011-0152 Installation Adding a Wireless Humidity SensorD-011-0152 D-011-0152 Installation D-011-0152D-011-0152 Select N.O. Contact or N.C. Contact InstallationD-011-0152 Verify Wireless Signal Strength D-011-0152Adding Wired Sensors Adding a Wired Temperature SensorAdding Wired Sensors Adding a Wired HA-III+Humidity SensorD-011-0152 Adding a Wired WaterBug Sensor Note A supervised WaterBug sensor must be usedSelect N.O. Contact or N.C. Contact Adding a Wired Contact Closure SensorD-011-0152 Adding a 4-20mASensor Configuring the Relays Operation Monitoring Environmental ConditionsViewing Sensor Settings Viewing Active AlarmsViewing the Alarm Log Viewing Pending Alarm InformationViewing Limit Settings Viewing the Event LogViewing the Sensor Log Viewing Firmware InformationOperation D-011-0152Viewing RF Information Viewing RF InformationMaintenance Locking and Unlocking the EA800Pausing Monitoring and Cancelling Pause Adding a Sensor Replacing a SensorEditing Sensor Parameters SENSORS screenDeleting a Sensor Reprogramming a RelayF3 F3 Changing the Date Format Changing the Time FormatChanging the Date or Time Setting Changing Sensor Data Collection FrequencyChanging the Buzzer Setting Changing the Buzzer SettingMaintenance Changing the PasswordD-011-0152 Clearing the Sensor Log Clearing the Alarm LogClearing the Alarm Log Maintenance Updating the FirmwareD-011-0152 Saving Configuration Settings F3 LOAD/SAVE CONFIG screenLoading Configuration Settings CONFIG screenExported Alarm Data Exporting the Stored LogsExported Event Data Exported Sensor Data12/24/2007 07 06 03 PM Sensor deletedExporting the Stored Logs D-011-0152Troubleshooting ACTIVE ALARMS screenVerifying RF Signal Strength Viewing Signal Strength for a Wireless SensorSpecifications Base Unit and Sensor SpecificationsAccessories Appendix A Screen Maps Figure 17. Locked Screen MapFigure 18. Unlocked Screen Map - Top Level D-011-0152Figure 19. Sensors Screen Map Appendix A Screen MapsD-011-0152 Figure 20. Add New Sensor Screen Map D-011-0152Appendix A Screen Maps Figure 21. Edit Sensor Screen MapFigure 22. Relay Screen Map D-011-0152Figure 23. Data Log Screen Map D-011-0152Figure 24. System Screen Map Appendix A Screen MapsD-011-0152 Figure 25. Configuration Screen Map D-011-0152Appendix B Planning Worksheet InstallationAlarm Condition Appendix B Planning WorksheetD-011-0152 C Wiring Diagram AppendixD-011-0152 Appendix D System Configuration Record Unit of Measure Appendix D System Configuration Record Sensor 6 Settings wireless Appendix D System Configuration Record D-011-0152 Warranty and Service Information Manufactured in the U.S.A by Winland Electronics1950 Excel Drive, Mankato, MN, Outside MN Phone Phone Fax