Manuals / Epson / Household Appliance / Furnace

Epson P)-1, HWDV080DV(N INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB, 24632-0-0508, Page

Models: P)-1 HWDV080DV(N

1 48

Download 48 pages 45.26 Kb

Page 29

INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB

INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB

1

Remove front panel of heater by opening, then lifting one side out then the other.

2

Disconnect the power cord from the blower assembly.

3

Remove ground screw from blower mounting bracket.

24632-0-0508

Page 29

Image 29

Epson P)-1 INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB, Remove ground screw from blower mounting bracket, 24632-0-0508

Contents

GAS-FIRED DIRECT VENT WALL FURNACETABLE OF CONTENTS INCLUDED IN THE BOX TOOLS NEEDED HARDWARE PACKETSADJUSTABLE WRENCH CAULKING SNIPS TAPE MEASURE SAW HEATER HARDWARE PACKETSPECIFICATIONS GAS SPECIFICATIONSHIGH ALTITUDE SPECIFICATIONS EXTERNAL DIMENSIONS INCHESNATURAL GAS OR PROPANE/LP UNIT DIMENSIONSPage 24632-0-0508Follow State and Local codes for installation IMPORTANT SAFETY INFORMATIONLP-GASWARNING ODOR SAFETY INFORMATION FOR USERS OF LP-GASNO ODOR DETECTED - ODOR FADE SOME POINTS TO REMEMBERInstructions to Installer INTRODUCTIONInstallation in Residential Garages Qualiﬁed Installing AgencyDIRECTLYBELOW. KEEPCLEAR OFALLOBSTRUC- TIONS” REQUIREMENTS FOR MASSACHUSETTSDescription TERMINATION CLEARANCESUS Installations1 Installing a New Main Gas Cock GAS SUPPLYMethod of Installing a Tee Fitting Sediment Trap Locating Gas SupplyCLEARANCES GAS SUPPLY continuedPressure Testing of the Gas Supply System Checking Manifold PressureLocation - All Models INSTALLATION INSTRUCTIONS OVERVIEWINSTALLATION OVERVIEW INSTALLATION AND ASSEMBLYINSTALLATION OF HOUSEWARMER PRODUCT INSTALLATION AND ASSEMBLYSEE OTHER SIDE FOR HWDV080 MOUNTING TEMPLATE FORHWDV181BDV ModelHWDV080BDV Pilot Hole INTERIOR INSTALLATION OF THE FRONT OF THE UNIT CAP LONG SCREWS SCREWS CUTTING THE VENT TUBESFLUE OUTLET TUBE AIR INLET TUBE MOUNTING PLATE Page CUTTING THE VENT TUBES4#10 x 2 ½” SCREWS EXTERIOR INSTALLATION OF THE VENTINGFLUE OUTLET TUBE COLLAR OF FLUE OUTLET EXTERIOR INSTALLATION OF THE VENTING3” DIA. VENT CAP COLLAR FURNACE CEMENT 3#10 x ½” SCREWS EXTERIOR INSTALLATION OF THE VENTING4#10 x 2 ½” SCREWS REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEMIf installing onto a vinyl sided exterior wall, attach vinyl siding vent shield using two of the screws that attach the outside wall plate REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEM3#10 x ½” SCREWS REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEMRemove ground screw from blower mounting bracket INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB24632-0-0508 PageROUTE CORDS THROUGH BOTTOM HOLE INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBReconnect power cord to blower assembly INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBof the heater INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBCHECK THE FOLLOWING BEFORE OPERATING APPLIANCE BEFORE OPERATING APPLIANCEATTENTION INSTALLER Do not use gases other than those indicated on the heater’s rating plate label BEFORE OPERATING APPLIANCEAvoid blocking air inlet and hot air outlet BEFORE OPERATING APPLIANCEWHAT TO DO IF YOU SMELL GAS BEFORE OPERATING APPLIANCEWHAT TO DO IF YOU SMELL GAS OPERATING INSTRUCTIONSFOR YOUR SAFETY READ BEFORE LIGHTING TO TURN OFF GAS TO APPLIANCE LIGHTING INSTRUCTIONSCONTROL KNOB INDICATOR GAS CONTROL KNOB SHOWN IN “OFF” POSITIONMAIN BURNER FLAME CHARACTERISTICS PILOT FLAME CHARACTERISTICSMAIN BURNER PILOT FLAME THERMOCOUPLE BURNER CHANNELFAULTS TO BE MAINTENANCE INSTRUCTIONSOPERATION FREQUENCYHOW TO ORDER REPAIR PARTS TROUBLESHOOTINGPROBLEM SOLUTIONINDEX NO PARTS LISTDESCRIPTION HWDV080INDEX NO PARTS LISTDESCRIPTION HWDV08024632-0-0508 PARTS VIEWPage Page SERVICE NOTES24632-0-0508 24632-0-0508 SERVICE NOTESPage Page SERVICE NOTES24632-0-0508 Empire Comfort Systems Inc HOUSEWARMER is a registered trademark ofFAX Page