Manuals / Epson / Household Appliance / Furnace

Epson P)-1 INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB, Reconnect power cord to blower assembly

Models: P)-1 HWDV080DV(N

1 48

Download 48 pages 45.26 Kb

Page 31

Image 31

INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB

Reconnect power cord to blower assembly.

Attach ground wires from the blower and power cord to the blower mounting bracket.

Slide fan control into the tabs on the right side of the chamber support.

24632-0-0508

Page 31

Image 31

Epson P)-1, HWDV080DV(N INSTALLATION OF OPTIONAL BLOWER KIT HW125SCB, Reconnect power cord to blower assembly

Contents

GAS-FIRED DIRECT VENT WALL FURNACETABLE OF CONTENTS INCLUDED IN THE BOX HEATER HARDWARE PACKET HARDWARE PACKETSTOOLS NEEDED ADJUSTABLE WRENCH CAULKING SNIPS TAPE MEASURE SAWEXTERNAL DIMENSIONS INCHES GAS SPECIFICATIONSSPECIFICATIONS HIGH ALTITUDE SPECIFICATIONS24632-0-0508 UNIT DIMENSIONSNATURAL GAS OR PROPANE/LP PageFollow State and Local codes for installation IMPORTANT SAFETY INFORMATIONSOME POINTS TO REMEMBER SAFETY INFORMATION FOR USERS OF LP-GASLP-GASWARNING ODOR NO ODOR DETECTED - ODOR FADEQualiﬁed Installing Agency INTRODUCTIONInstructions to Installer Installation in Residential GaragesDIRECTLYBELOW. KEEPCLEAR OFALLOBSTRUC- TIONS” REQUIREMENTS FOR MASSACHUSETTSUS Installations1 TERMINATION CLEARANCESDescription Locating Gas Supply GAS SUPPLYInstalling a New Main Gas Cock Method of Installing a Tee Fitting Sediment TrapChecking Manifold Pressure GAS SUPPLY continuedCLEARANCES Pressure Testing of the Gas Supply SystemLocation - All Models INSTALLATION INSTRUCTIONS OVERVIEWINSTALLATION OVERVIEW INSTALLATION AND ASSEMBLYINSTALLATION OF HOUSEWARMER PRODUCT INSTALLATION AND ASSEMBLYSEE OTHER SIDE FOR HWDV080 MOUNTING TEMPLATE FORHWDV080BDV ModelHWDV181BDV Pilot Hole INTERIOR INSTALLATION OF THE FRONT OF THE UNIT FLUE OUTLET TUBE AIR INLET TUBE MOUNTING PLATE CUTTING THE VENT TUBESCAP LONG SCREWS SCREWS Page CUTTING THE VENT TUBES4#10 x 2 ½” SCREWS EXTERIOR INSTALLATION OF THE VENTING3” DIA. VENT CAP COLLAR FURNACE CEMENT EXTERIOR INSTALLATION OF THE VENTINGFLUE OUTLET TUBE COLLAR OF FLUE OUTLET 3#10 x ½” SCREWS EXTERIOR INSTALLATION OF THE VENTING4#10 x 2 ½” SCREWS REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEMIf installing onto a vinyl sided exterior wall, attach vinyl siding vent shield using two of the screws that attach the outside wall plate REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEM3#10 x ½” SCREWS REASSEMBLY AND RESEALING VENT-AIRINTAKE SYSTEMPage INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBRemove ground screw from blower mounting bracket 24632-0-0508ROUTE CORDS THROUGH BOTTOM HOLE INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBReconnect power cord to blower assembly INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBof the heater INSTALLATION OF OPTIONAL BLOWER KIT HW125SCBATTENTION INSTALLER BEFORE OPERATING APPLIANCECHECK THE FOLLOWING BEFORE OPERATING APPLIANCE Do not use gases other than those indicated on the heater’s rating plate label BEFORE OPERATING APPLIANCEAvoid blocking air inlet and hot air outlet BEFORE OPERATING APPLIANCEWHAT TO DO IF YOU SMELL GAS BEFORE OPERATING APPLIANCEFOR YOUR SAFETY READ BEFORE LIGHTING OPERATING INSTRUCTIONSWHAT TO DO IF YOU SMELL GAS SHOWN IN “OFF” POSITION LIGHTING INSTRUCTIONSTO TURN OFF GAS TO APPLIANCE CONTROL KNOB INDICATOR GAS CONTROL KNOBBURNER CHANNEL PILOT FLAME CHARACTERISTICSMAIN BURNER FLAME CHARACTERISTICS MAIN BURNER PILOT FLAME THERMOCOUPLEFREQUENCY MAINTENANCE INSTRUCTIONSFAULTS TO BE OPERATIONSOLUTION TROUBLESHOOTINGHOW TO ORDER REPAIR PARTS PROBLEMHWDV080 PARTS LISTINDEX NO DESCRIPTIONHWDV080 PARTS LISTINDEX NO DESCRIPTIONPage PARTS VIEW24632-0-0508 24632-0-0508 SERVICE NOTESPage Page SERVICE NOTES24632-0-0508 24632-0-0508 SERVICE NOTESPage Page HOUSEWARMER is a registered trademark ofEmpire Comfort Systems Inc FAX