When You Suspect a Problem

49

Only part of the image is displayed (large/small)

 

 

 

 

 

 

 

 

 

 

 

• Change the resolution for the notebook

Change the resolution so that the image is displayed in the whole of the

 

 

 

 

 

 

 

 

 

 

 

computer or computer with an LCD screen.

projection area, or set the image signal to external output only. See “Selecting

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the Input Source” on page 28.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Is the aspect ratio set correctly?

Press the [Aspect] button to set the aspect ratio to 4:3. See “Projecting in

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

widescreen (changing aspect ratio)” on page 31.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Has the computer been set for dual display?

If dual display has been activated in the Display Properties of the connected

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

computer’s Control Panel, the projector will only display about half of the image

 

 

 

 

 

 

 

 

 

 

 

 

on the computer screen. To display the whole of the image on the computer

 

 

 

 

 

 

 

 

 

 

 

 

screen, turn off the dual display setting. Refer to the video driver manual for the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

computer’s monitor for further details.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Has the correct resolution been selected?

Set the computer so that the signals that are output are compatible with this

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

projector. Please refer to your computer’s documentation for further details. See

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“Supported Display Resolutions” on page 64.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Has the position been adjusted correctly?

Use the “Setting”“Screen”“Position” configuration menu to correctly

 

 

 

 

 

 

 

 

 

 

 

 

adjust the display position. See “Setting menu” on page 39.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Is the E-Zoom function being used to enlarge

Press the [Esc] button on the remote control to cancel E-Zoom.

 

 

 

 

 

 

 

 

 

 

 

the image?

See “E-Zoom” on page 31.