Manuals
/
Exmark
/
Lawn and Garden
/
Lawn Mower
Exmark
Lazer HP manual Electrical Diagram
Models:
Lazer HP
1
53
60
60
Download
60 pages
15.67 Kb
50
51
52
53
54
55
56
57
<
>
Troubleshooting
Specifications
Install
Service Interval Refer to chart
Warranty
Dimension
Maintenance
Problem
Caster Wheel Assembly
Height Adjustment Plate
Page 53
Image 53
8. ELECTRICAL DIAGRAM
- 48 -
Page 52
Page 54
Page 53
Image 53
Page 52
Page 54
Contents
Part No. 103-5505 Rev. A
For Serial Nos 440,000 & Higher
The enclosed Engine Owner’s Manual is supplied for information regarding The U.S. Environmental Protection Agency EPA and the California Emission Control Regulation of emission systems, maintenance and warranty
How the Program Works
EXMARK PARTS PLUS PROGRAM
EFFECTIVE DATE September 1 Program
CAREFULLY READ THIS MANUAL IN ITS ENTIRETY
OPERATORS MANUAL
BEFORE OPERATING YOUR MOWER
1. SAFETY
TABLE OF CONTENTS
2. SPECIFICATIONS
3. ASSEMBLY INSTRUCTIONS
ATTENTION! BECOME ALERT YOUR SAFETY IS INVOLVED
1. SAFETY
1.1 SAFETY ALERT SYMBOL
1.2 TRAINING
DANGER
DANGER
1.4 OPERATION
DANGER
SAFE ZONE FOR MOWING
HOW TO AVOID THE HAZARD
There is no rollover protection when the roll bar is down
Lower the roll bar only when absolutely necessary
Do not wear seat belt when the roll bar is down
1.5 MAINTENANCE AND STORAGE
For Kawasaki Liquid-Cooled units
1.6 SAFETY SIGNS
LOCATION Left and Right Corners of Mower Deck
LOCATION On Tilt Switch
LOCATION Left of Center on Mower Deck, Under Floor Pan
LOCATION Top of console
LOCATION RH Side on Top
Height Adjustment Plate
LOCATION Top of Right Engine Baffle
Rear of Mower Deck
2.1 MODEL NUMBER
2. SPECIFICATIONS
2.2 ENGINE
2.3 FUEL SYSTEM
2.8 HYDROSTATIC GROUND DRIVE SYSTEM
2.7 SEAT
2.9 TIRES
2.10 CUTTING DECK
minimum125 ft-lbs
2.11 DIMENSIONS
2.12 TORQUE REQUIREMENTS
3.1 UNCRATE MOWER 3.2 INSTALL ROLLOVER PROTECTION SYSTEM ROLL BAR
3. ASSEMBLY INSTRUCTIONS
LOWER ROLL BAR INSTALLATION
UPPER ROLL BAR INSTALLATION
3.3 SERVICE BATTERY
The machine is shipped with a filled lead acid battery
DANGER
3.5 CHECK TIRE PRESSURE
3.4 INSTALL DRIVE WHEELS
3.6 INSTALL MOTION CONTROL LEVERS
3.9 SERVICE ENGINE COOLANT
3.8 SERVICE ENGINE
3.7 POSITION DISCHARGE CHUTE
CONTROL ARM SHAFT
4. OPERATION INSTRUCTIONS
3.10 SERVICE HYDRAULIC OIL
4.1 CONTROLS
MOTION CONTROL POSITIONS
Page
Push the lever forward and down to disengage the brake
4.3 OPERATING INSTRUCTIONS
4.2 PRE-START
IMPORTANT Operator must be in seat before the PTO can be engaged
4.4 TRANSPORTING
DANGER
DANGER
HOW TO AVOID THE HAZARD
HOW TO AVOID THE HAZARD
Use extreme caution when operating a unit on a ramp
POTENTIAL HAZARD
5.1 PERIODIC MAINTENANCE
5. MAINTENANCE & ADJUSTMENTS
Service Interval Daily
Service Interval Daily
Service Interval Monthly
Service Interval Daily
Service Interval Daily or more often in dry conditions
Service Interval Daily
TORQUE TO 115-120ft-lbs. 156-163N-m
BLADE BOLT INSTALLATION
Service Interval Daily
See Engine manual for additional information
Service Interval 50 hrs More often under severe conditions
NOTE If machine does not pass any of these tests, do not operate. Contact your authorized EXMARK SERVICE DEALER
Service Interval Daily
It is recommended to service at whichever interval happens first
Service Interval 50 hours
Service Interval 100 hrs
COOLANT PLUG LOCATION
Service Interval 40 hrs
Service Interval 40 hr
For units with Pneumatic Caster tires with a valve stem
For units with Semi-Pneumatic Caster tires without a valve stem
Service Interval 40 hrs
LUBRICATION CHART
Service Interval Refer to chart
Service Interval 160 hrs
Service Interval Once Yearly
CASTER WHEEL ASSEMBLY
Service Interval After First 250 hrs Then yearly thereafter
Service Interval As Required
Service Interval 160 hrs
Service Interval 160 hrs
Service Interval 500 hrs
5.2 ADJUSTMENTS
CUTTING HEIGHT POSITION
ANTI-SCALP ROLLER ADJUSTMENT
SWIVEL ADJUSTMENT SPRING COMPRESSION ADJUSTMENT
MULE DRIVE BELT ADJUSTMENT
3/16” 4.8 mm to 1/4” 6.4 mm 2.75” 7.0 cm
BRAKE ADJUSTMENT
BELT GUIDE POSITIONING
THROTTLE TENSION
No adjustment necessary
REVERSE INDICATOR ADJUSTMENT
MOTION CONTROL ADJUSTMENT
ARMREST ADJUSTMENT
CASTER ADJUSTMENT
6. WASTE DISPOSAL
6.3 MERCURY SWITCH DISPOSAL
6.1 MOTOR OIL DISPOSAL
6.2 ENGINE COOLANT DISPOSAL
6.4 BATTERY DISPOSAL
7. TROUBLE SHOOTING
7.1 MOWER PULLS LEFT OR RIGHT W/LEVERS FULLY FORWARD
7.2 MOWER CUTS UNEVENLY
PROBLEM
ENGINE TROUBLESHOOTING TABLE
7.4 ENGINE WARNING SYSTEMS
Check for dirty radiator core
8. ELECTRICAL DIAGRAM
9. HYDRAULIC DIAGRAM
10.Limited Warranty Exmark Turf Equipment
Page
Page
Date
SERVICE RECORD
Description of Work Done
Done By
Page
LAZER Z
MICRO-MULCH ACCESSORY
LAZER Z HP
LAZER Z XP