Manuals / Extron electronic / Computer Equipment / Network Card

Extron electronic 134xi, 130xi Setting internal jumpers, 2-16, 15 - Opening the interface cover

Models: 134xi 150xi 130xi

1 38

Download 38 pages 16.66 Kb

Page 23

Setting internal jumpers

Setting internal jumpers

The jumpers inside the interface(s) are set at the factory for optimal use by most systems. However, you can change a jumper setting to meet the needs of a particular system.

The user-configurable, internal jumpers control the following functions:

•horizontal and vertical sync polarity

•vertical sync pulse width.

Follow these steps to change the jumper settings. The RGB 134xi is shown for illustration, but the steps apply to all interfaces.

1.Remove power from the interface by disconnecting the AC power cord from the unit.

2.Open the cover of the interface (the top half of the enclosure), as shown below. Remove the screws from the enclosure, and lift the cover straight up.

Do not touch any switches or electronic components inside the interface. Doing so could damage the interface.

Slide cover back slightly, lift straight up.

AUDIO

INPUT

MBC

POWER

H.	SHIFT	UNIVERSAL	RGB
	SHIFT	H.	RGB	134 xi
		H.	INTERFACE W	134 xi
		SHIFT		/ADSP
			MIN/MAX

Remove (6)

Screws

Figure 2-15 — Opening the interface cover

3.Note the positions of jumpers J20 and J40 before changing jumper settings. The illustration of the following circuit board shows the locations of the J20 and J40 jumpers. There are two possible setting combinations for 3-pin jumpers:

RGB 130xi , 134xi , 150xi Controls and Installation

2-16

Image 23

Extron electronic 134xi, 130xi, 150xi user manual Setting internal jumpers, 2-16, 15 - Opening the interface cover

Contents

User’s Manual Universal InterfacesRGB Consignes de Sécurité Français PrecautionsRGB 130xi , 134xi , 150xi Table of Contents Safety Instructions EnglishRGB 130xi , 134xi , 150xi Table of Contents Table of ContentsChapter 2 Controls and Installation RGB 130xi , 134xi RGB 130xi About this Manual About the Interfaces FeaturesChapter1One IntroductionAbout the Interfaces FeaturesIntroduction About this ManualRGB Controls and InstallationFront and Rear Panels Installation Chapter2TwoFront and Rear Panels Controls and InstallationRGB 150xi front panel features 2-1 RGB 130xi , 134xi , 150xi Controls and InstallationFigure 2-2 - RGB 150xi rear panel RGB 150xi rear panel featuresRGB 130xi , 134xi , 150xi Controls and Installation Figure 2-3 - RGB 130xi front panel Controls and Installation, cont’dRGB 130xi front panel features 2-3 RGB 130xi , 134xi , 150xi Controls and InstallationRGB 130xi , 134xi , 150xi Controls and Installation RGB 130xi rear panel featuresFigure 2-4 - RGB 130xi rear panel Controls and Installation, cont’d RGB 134xi front panel features2-5 RGB 130xi , 134xi , 150xi Controls and Installation Figure 2-5 - RGB 134xi front panelRGB 130xi , 134xi , 150xi Controls and Installation RGB 134xi rear panel featuresFigure 2-6 - RGB 134xi rear panel Controls and Installation, cont’d InstallationEasy setup procedure 2-7 RGB 130xi , 134xi , 150xi Controls and InstallationRGB 130xi , 134xi , 150xi Controls and Installation Mounting the interfaceFigure 2-7 - Attaching the under desk brackets Figure 2-8 - Mounting the interface under a deskControls and Installation, cont’d 2-9 RGB 130xi , 134xi , 150xi Controls and InstallationFigure 2-9 - Attaching the through desk brackets Figure 2-10 - Mounting the interface in a tableCabling Figure 2-11 - RGB 130xi installationFigure 2-12 - RGB 134xi installation RGB 130xi , 134xi , 150xi Controls and InstallationControls and Installation, cont’d 2-11 RGB 130xi , 134xi , 150xi Controls and InstallationFigure 2-13 - RGB 150xi installation Figure 2-14 - Fastening captive screws Connecting audio output2-12 Unbalanced audioControls and Installation, cont’d 2-13 RGB 130xi , 134xi , 150xi Controls and InstallationBalanced audio RGB 130xi , 134xi , 150xi Controls and Installation Setting the DIP switches2-14 appropriate end of each switch75 Ohm input termination 2-15 RGB 130xi , 134xi , 150xi Controls and InstallationControls and Installation, cont’d SERR serration pulseRGB 130xi , 134xi , 150xi Controls and Installation Setting internal jumpers2-16 Figure 2-15 - Opening the interface coverControls and Installation, cont’d 2-17 RGB 130xi , 134xi , 150xi Controls and InstallationFigure 2-17 - Changing jumper settings Figure 2-16 - Circuit board jumper locationsThe jumpers perform the following functions 2-18RGB 130xi , 134xi , 150xi Controls and Installation 2-19 RGB 130xi , 134xi , 150xi Controls and Installation RGB 130xi ,134xi ,150xi Specifications Accessories and Part Numbers Mounting TemplatesAAppendix Video output Specifications - RGB 130xi, 134xi Video inputAppendix Video throughputGeneral Audio inputAudio throughput Audio outputSpecifications are subject to change without notice Appendix, cont’dA-3 RGB 130xi, 134xi, 150xi Appendix Thunder Mounting Kits Accessories and Part NumbersSignal input cable kits for RGB RGB 130xi , 134xi , 150xi AppendixMiscellaneous A-5 RGB 130xi, 134xi, 150xi AppendixAppendix, cont’d BNC cablesRGB 130 xi , 134 xi , 150 xi Appendix A-7 RGB 130xi, 134xi, 150xi Appendix RGB 130 xi , 134 xi , 150 xi Appendix A-9 RGB 130xi, 134xi, 150xi Appendix FCC Class A Notice Extron’s Warranty+65.226.0015 FAX +65.226.0019 Singapore EXTRONFAX 714.491.0192 24-hour access - worldwideThe Netherlands EXTRON ELECTRONICS, ASIA