Rev. D
Installation Guide for the PVS 200, 300, and
PoleVault Systems
68-1390-01
Sicherheitsanleitungen Deutsch
Precautions
Safety Instructions English
Consignes de Sécurité Français
The PoleVault System
PoleVault Systems Installation Introduction
Introduction
Overview
Extron Cables & Notes
PoleVault System installation and wiring overview
1-2 PoleVault Systems Installation Introduction
Introduction, contd
1. Room layout
Before you Begin Installation - Planning
Typical classroom installation
PoleVault Systems Installation Introduction - Planning
b. Location of the screen and projector
Example of a classroom installation
1-4 PoleVault Systems Installation Introduction - Planning
Introduction - Planning, cont’d
Location of source devices
Example classroom with four speaker installation
Viewing obstructions
c. Location of MediaLink Controller and Wall Plates
a. Included items
1-6 PoleVault Systems Installation Introduction - Inventory Overview
Introduction - Inventory Overview
2. Inventory
PVT CV D
PoleVault Systems Installation Introduction - Inventory Overview
PoleVault System Devices and Hardware, contd
PoleVault System Devices and Hardware, cont’d
PV SI 3C LP
1-8 PoleVault Systems Installation Introduction - Inventory Overview
Introduction - Inventory Overview, cont’d
PoleVault System Ceiling Speakers
b. Items not included
PoleVault Systems Installation Introduction - Inventory Overview
Document camera and cables
Introduction - Inventory Overview, cont’d
d. Installation tools
Stage Three - Install the PV SI 3C LP Ceiling Speakers
Installation Overview
Outline of installation steps
Stage One - Install the Screen and Projector
PCM 240 Projector Ceiling Mount
Where it goes Screws up into PCM
Adjuster Plate
2-2 PoleVault Systems Installation Installation - Stage
2d Screw the adjuster plate onto the PMP
When marking the center line of the screen
PMP installed onto PCM
2c Install the PMP
3. Verify the image location
Installation - Stage One, cont’d
2f Slide and lock the projector onto the adjuster plate
2-4 PoleVault Systems Installation Installation - Stage
Mark and start cutting the hole on the
installation
4. Cut the ceiling tile
4b Take measurements with the PCM 240 on the T-bar
6a Attach turnbuckles at the corners
6b Mark structural ceiling for lag bolt installation
2-6 PoleVault Systems Installation Installation - Stage
6. Secure the Projector Ceiling Mount to the ceiling
T Use S-hooks to hang the screen from the brackets
7. Install the Screen
6g Attach the safety cable to the PCM
T Power outlet installation on the PCM
Stage
Stage Two - Install the Wall Plates and MLC 104 IP
This stage involves installing the devices shown below
2-8 PoleVault Systems Installation Installation - Stage
Cables
PVT transmitter installation
MLC 104 IP Plus installation
PVS 204SA switcher
T Use a level when marking the holes
Stage Two - Install the Wallplates and MLC 104 IP Plus
1. Install mud rings
If a suitable wall box is already installed, follow step 2 onwards
Label color
Signal Cable
2. Pull cables
T Secure cables with cable clamps to provide strain relief
3b Mount the PVT in the mud ring, then
Installation - Stage Two, cont’d
3. Install wall plates
2-12 PoleVault Systems Installation Installation - Stage
4a Connecting the MLC to the switcher
4. Install MediaLink Controller
TWire stripping lengths
Wire color
an RS-232 cable or IR emitter cable, as
4c Connect to the LAN using a CAT 5 cable
2-14 PoleVault Systems Installation Installation - Stage
Connect the MLC to the projector with
PoleVault Systems Installation Installation - Stage
Connections made to the MLC 104 IP Plus
4e Secure the MLC 104 IP Plus to the mud ring
2-15
2-16 PoleVault Systems Installation Installation - Stage
Stage Three - Install the PV SI 3C LP Ceiling Speakers
Speaker Installation
Speaker cable connects ceiling speakers to the PVS 204SA switcher
the cross marks with those on the supplied template
1. Cut ceiling tile
Measure and mark the center point of the tile and align
1b Mark the tile and cut the hole
2e Turn and lock down the four dog legs on the C‑ring
Installation - Stage Three, cont’d
2-18 PoleVault Systems Installation Installation - Stage
4. Cable the speakers
c. To terminate the cable, strip the end of the cable
4-pole captive screw connector
4c Wire the captive screw connector Dual mono output
Stereo or dual mono output using parallel speaker wiring
Installation - Stage Three, cont’d
5. Finish speaker installation
2-20 PoleVault Systems Installation Installation - Stage
5a Apply putty to speaker grill
PoleVault Systems Installation Installation - Stage 4
Stage Four - Install the PMK 450 and the PVS 204SA
This stage covers installing the devices shown below
PVS 204SA PoleVault Switcher
2-22 PoleVault Systems Installation Installation - Stage
Installation - Stage Four, cont’d
2. Install the PMK 450 Pole Mount kit
Switcher and projector cable overview
3c Wire the captive screw connector for the power supply
3. Install the PVS 204SA switcher
to the cord of the supplied power source and connect the
power cord to the rear of switcher
N Do not thread the power cable through the
4. Finish installing the Pole Mount kit
BControl/power cable from the MLC 104 IP Plus
FPower supply cable. Do not apply power yet
4d Replace projector on the adjuster plate
4c Attach and screw down rear plate
PoleVault Systems Installation Installation - Stage 4
1c Launch the Global Configurator 2 program
Stage Five - Configure the System
1. Configure the system
1a Load Global Configurator 2 software
Select MLC 104 IP Plus/PoleVault System from the drop down box
2-27
PoleVault Systems Installation Installation - Stage
2-28 PoleVault Systems Installation Installation - Stage
Installation - Stage Five, cont’d
2a Turn on the MLC 104 IP Plus controller and the PVS 204Sa switcher
2c Check that an image is present, adjust as needed
PoleVault Systems Installation Installation - Stage
3. Final installation
2e Set MLC volume to maximum, and adjust the level on the switcher
2-29
2-30 PoleVault Systems Installation Optional Accessory Installation
Optional Accessory Installation - PPC
Installation Procedure
4 Open the sensor and loop a wire around the sensor
7. Strip 3/16 of insulation from each conductor on the bare
PoleVault Systems Installation Optional Accessory Installation
10 Connect the power supply via the PoleVault switcher
2-32 PoleVault Systems Installation Optional Accessory Installation
Optional Accessory Installation - PPC
PoleVault Systems Installation Optional Accessory Installation
Testing and Adjustment Procedure
3 / 4 Sensitivity knob adjustment
5 Priority Page Controller Time DIP switch settings
Reference Information
Specifications
N Specifications are subject to change without notice
2-34 PoleVault Systems Installation Reference Information
PVT CV D and PVT RGB D
PoleVault Systems Installation Reference Information
Devices PVS 204SA
MLC 104 IP Plus
2-36 PoleVault Systems Installation Reference Information
Installation - Reference Information, cont’d
PoleVault Switcher
16-18 lbs 7.3-8.2 kg Projector weight must not exceed 25 lbs 11.3 kg
Page
Stage Four - Install the PMK 450 and the PVS 204SA
Outline of installation steps
Stage One - Install the Screen and Projector
Stage Three - Install the PV SI 3C LP Ceiling Speakers