Manuals / Fujitsu / Computer Equipment / Laptop

Fujitsu 5000 user manual Point, Remove the expansion card mounting bracket, Remove the slot cover

Models: 5000

1 72

Download 72 pages 40.94 Kb

Page 63

Image 63

3Remove the expansion card mounting bracket.

Remove the two screws and pull straight up the expansion card mounting bracket

When an expansion card has been installed, remove the cable from the card and remove the bracket.

4Remove the slot cover.

Remove one screw from the position where the expansion card is installed, and remove the slot cover.

Point

Keep the removed slot cover.

Use the cover to keep an empty slot from dust.

Page 63

Image 63

Fujitsu 5000 user manual Point, Remove the expansion card mounting bracket, Remove the slot cover

Contents

DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Page For Safe Operation Before reading this manualBacking Up the Data Using this Product for High-Safety ApplicationsMicrosoft Service Pack Warning messages Conventions Used in This ManualPoint Symbols used in the textRepresentation for BIOS Setup viiiCommand entry keying in CD-ROM drive\setup.exe Screenshot example and illustrationsProduct name Reference to productsIn this manual, the product names are referred to as follows This manual includes information on other operating systemsDisposal of batteries RecyclingDisposal of the PC unit Disposal of the LCD unitFUJITSU LIMITED Warning and caution labelsDESKPOWER Rear of the PC main unitChapter 3 Hardware Chapter 2 Installation and ConnectionOrganization of This Manual Chapter 1 Part NamesHardware ContentsInstallation and Connection Part NamesCHAPTER System ExpansionTechnical Information Installing Memory ModulesCHAPTER Part Names 2 Power lamp 1 Part Names and FunctionsFront of the PC Unit 1 Power button11 Floppy disk access lamp 3 Disk access lamp4 USB connector 7 CD access lamp2 Expansion card slots Rear of the PC Unit5 Keyboard connector Connect the keyboard 1 Burglarproof lock9 LAN connector Connect a LAN cable 6 Serial connector7 Parallel connector 8 CRT connector2 Expansion card slots Inside the PC Unit3 Power supply unit 1 Internal hard disk drive6 Internal battery Motherboard3 Secondary IDE connector IDE2 4 Floppy disk drive connector FDD 5 Primary IDE connector IDE1CHAPTER Installation and ConnectionVertical Placement 1 InstallationLocation of Installation Mounting Feet2 Place the PC on the disassembled foot When using a single footHorizontal Placement 1 Disassemble the foot 1 Disassemble the footPoint Example of InstallationTo locate the PC, follow the procedure below Vertical PlacementPoint Horizontal Placement2 Connection 3 Connecting the mouse Connecting the Display/Keyboard/Mouse1 Plugging the power cord into power receptacle 2 Plugging the power cord into inlet of display unit5 Connecting the display cable to the PC unit 4 Connecting the keyboardConnect the Power Cord 1 Plug the power cord into the power inlet at the rear of the PC 2 Connect the power cord to the 230 VAC power sourcePlug the other end of power cord into the 230 VAC power receptacle Cautions 3 Power On2 Press the PC power button How to Power OnConsiderations 4 Setting UpPoint Setting Up Windows XP10 Enter the password and click → Point13 Click OK. The PC restarts Setting Up Windows PointPoint 12 Click Perform10 Click User for this computer... and Next 6 Click Standard setting and NextPoint 9 Click Next14 Select Restart and click OK Point11 Click Finish 13 Click Start → ShutdownProblem During Setup? 5 Turn Off the Computer How to Turn OffPoint For WindowsFor Windows Me CHAPTER Hardware 1 Esc key 1 Keyboard7 Indicators Point10 Windows key Point8 Caps Lock key 9 Ctrl keyNotes on Handling 2 CDsNotes on Using the Drive Point1 Press the CD eject button Inserting or Removing a CDPoint Inserting a CDPoint Removing the CD4 Manually push the tray until it clicks Inserting or Removing a Floppy Disk Point 3 Floppy Disks2 Press the Floppy disk eject button. The floppy disk comes out 1 Make sure that the floppy disk access lamp is offPoint Removing a Floppy DiskPoint 4 Hard Disk2 Remove the ball and clean it with water 5 Maintenance of the HardwareMaintenance of the PC Unit Maintenance of the Mouse3 Clean the inside of the mouse Maintenance of the KeyboardCleaning CDs Cleaning the Floppy Disk DriveCHAPTER System ExpansionNotes on Handling 1 Before Installing a Peripheral DeviceAfter removing the feet, place the PC unit on a soft cloth 1 Remove the two screws on the PC unit 2 Remove the upper cover 2 Removing the CoverRemoving the Cover PointPoint 3 Installing Memory ModulesMemory Module Combinations Location of Memory Modules Applicable Memory Modules4 Pull the hooks on both sides of the slot outward Installing Memory Modules1 Unplug the PC 2 Remove the upper cover 3 Remove the expansion card mounting bracket and reinforcing fittingPoint 7 Installing Memory Modules Reinstall the upper coverPoint 4 Installing an Expansion CardInstalling an Expansion Card Location of expansion Cards Applicable Expansion Cards1 Unplug the PC 2 Remove the upper cover Point 3 Remove the expansion card mounting bracket4 Remove the slot cover Point 6 Install the expansion card mounting bracket7 Reinstall the upper cover PointCHAPTER Technical Information PC Specifications 1 List of SpecificationsPoint Power/FrequencyOuter dimensions WeightLAN function PointLAN Controller CRT connector 2 Connector SpecificationsParallel connector LAN connector 100BASE-TX/10BASE-TSerial connector Mouse connectorKeyboard Connector Symbol Glossary