Manuals / Fujitsu / Computer Equipment / Computer Drive

Fujitsu MCE3064AP, MCF3064AP, MCE3130AP manual Confirming initial operations

Models: MCE3130AP MCE3064AP MCF3064AP

1 175

Download 175 pages 7 Kb

Page 67

3)Connect the AT interface cable.

4)After each cable connector is connected, secure the cable so that the cable does not touch the drive or the parts on the PCA or obstruct the flow of cooling air in the system cabinet.

3.9Operation Confirmation and Preparation for Use after Installation

3.9.1Confirming initial operations

This section provides the operation check procedures after the power is turned on.

(1)Initial operation when the power is turned on

#When the power is turned on, the drive starts initial self-diagnosis. The LED on the front panel is on for 1 second during initial self-diagnosis.

#If an error is detected during initial self-diagnosis, the LED on the front panel blinks.

#In case of not inserted the cartridge, when the power is turned on, the eject motor automatically turns once.

(2)Checks if errors occur at initial self-diagnosis

#Make sure that the cables are connected correctly.

#Make sure that the supply voltage is correct. (Measure the voltage at the power supply connector of the optical drive.)

#Make sure that the settings of all terminals are correct.

#If the LED on the front panel blinks continuously, an error was detected during initial self- diagnosis. In this case, issue the REQUEST SENSE command from the initiator (host system) to obtain sense data for error analysis.

The BUSY LED is on while the optical disk drive is executing seek, write, or read operations. The BUSY LED is on momentarily, so it seems as if it blinked or is off.

The eject motor turns once when the power is turned on so that in case the spindle motor position deviates due to shocks received by the drive during transport the position is corrected to allow the cartridge to be inserted normally. If the cartridge fails to be inserted, remove the cartridge and turn on the drive power to turn the eject motor once and reinsert the cartridge.

C156-E142-02EN

3 - 21

Image 67

Fujitsu MCE3064AP manual Confirming initial operations, Operation Confirmation and Preparation for Use after Installation

Contents

C156-E142-02EN MCE3130AP, MCE3064AP MCF3064AP OPTICAL DISK DRIVES PRODUCT MANUALAll Rights Reserved. Copyright ! 2001 FUJITSU LIMITED The contents of this manual is subject to change without prior noticeDate published Revised contentsREVISION RECORD EditionChapter 6 DIAGNOSIS AND MAINTENANCE Chapter 2 SPECIFICATIONSChapter 3 INSTALLATION REQUIREMENTS Chapter 5 OPERATION AND CLEANINGConventions for Alert Messages C156-E142-02EN DISCLAIMERHold the mounting frame when handling the drive. Do Low temperature burnsThe surface temperatures of some ICs on the printed circuit board Use an antistatic mat and wrist strap when handling the1 Make sure that the system power is off Be sure to turn on the power supply before inserting your cartridgeand enables you to insert the cartridge turn on the power supply beforehandMAINTENANCE AND DIAGNOSIS FAULT ANALYSIS MCE3064AP and MCF3064AP OPTICAL DISK DRIVE MAINTENANCE MANUALGENERAL DESCRIPTION SPECIFICATIONS INSTALLATION REQUIREMENTS HOST INTERFACE OPERATION AND CLEANING DIAGNOSIS AND MAINTENANCEStandards Institute REFERENCED STANDARDSCHAPTER CONTENTSSPECIFICATIONS INSTALLATION REQUIREMENTSCHAPTER HOST INTERFACEReset response Error registerATA Features register ATAPI Features registerERASE command SERVICE XA2 Not supportedSET FEATURES XEF Packet CommandsABBREVIATIONS CHAPTER 5 OPERATION AND CLEANINGCHAPTER 6 DIAGNOSIS AND MAINTENANCE GLOSSARYFIGURES Cleaning procedure Cleaning procedureCleaning procedure Cleaning procedureTABLES IDLE IMMEDIATE command EXECUTE DEVICE DIAGNOSTIC commandGET MEDIA STATUS command Error registerDefault values for the removable block access capabilities page Default values for the cashing pageRemovable block access capabilities page Changeable values in the removable block access capabilities pageSYNCHRONIZE CACHE command SEND DIAGNOSTIC commandSEEK command START/STOP UNIT command1.1 Features 1.1 Features 1.2 Drive Configuration 1.3 System ConfigurationCHAPTER 1 GENERAL DESCRIPTION 1.1.1 Performance 1.1.3 Maintainability/operability 1.1.2 Reliability1.1.4 Adaptability 1.1.5 Interface Page C156-E142-02EN 1.2 Drive Configuration 1.2.1 Drive modelFigure 1.1 Outer view with panel Figure 1.2 Outer view without panel Figures 1.1 and 1.2 show the outer viewFigure 1.3 Optical disk drive configuration 1.2.3 Mechanical sections 1.2.2 Configuration1.2.4 Control circuit section Figure 1.4 Control circuit section block diagramThe drive circuit section consists of the following circuits Laser diode control circuit Signal reproduction circuit1 ATAPI controller circuit section 2 Drive circuit sectionFigure 1.5 System configuration with one optical disk drive 1.3 System ConfigurationFigure 1.6 System configuration with two optical disk drives 2.1 Optical Disk Drive Specifications 2.1.1 Model and product number CHAPTER 2 SPECIFICATIONS2.1 Optical Disk Drive Specifications 2.2 Optical Disk Cartridge Specifications 2.3 Defect ManagementC156-E142-02EN Table 2.1 Model and order number 2 ofMCE3130AP 2.1.2 Drive specificationsTable 2.2 Specifications 1 of Table 2.2 lists MCE3130AP, MCE3064AP, MCF3064AP drives specificationsMCE3064AP Table 2.2 Specifications 2 ofC156-E142-02EN MCF3064AP Table 2.2 Specifications 3 ofC156-E142-02EN Table 2.2 Specifications 4 of Table 2.3 Environmental and power requirements 1 of 2.1.3 Environmental and power requirementsNo cartridge, power ON 2.1.4 Error rate Table 2.3 Environmental and power requirements 2 of2.1.5 Reliability 2.2.1 Recommended optical disk cartridge specifications 2.2 Optical Disk Cartridge SpecificationsTable 2.4 Recommended optical disk cartridge specifications ∃ Shutter open 2.2.2 Optical disk cartridgeFigure 2.1 Optical disk cartridge ∃ Shutter closed 2 Shutter 1 Cartridge case 3 Write protect tab3 Write protect tab The write protect tab selects whether write is enabled or disabled1 Cartridge case 2 ShutterDisk specifications 2.2.3 Disk specificationsa Sector slipping algorithm b Linear replacement algorithm 2.3 Defect Management 2.3.1 Defect management schematic diagramFigure 2.2 Algorithms for alternate processing C156-E142-02EN Figure 2.3 Example of alternate processing3.9 Operation Confirmation and Preparation for Use after Installation CHAPTER 3 INSTALLATION REQUIREMENTS3.3 Power supply Requirements 3.4 Cable Connections 3.5 Jumper Settings 3.6 Notes on Drive Handling 3.7 Mountingb IC controller, read map Figure 3.1 Surface temperature measurement pointsa Inside optical disk cartridge Operating of inner partition wall Tip of thermocouple Hole for inserting thermocoupleTable 3.1 Temperature requirements at measurement points 3.1.2 Temperature requirements and measuring method3.1.3 Air flow Table 3.2 Temperature at each measuring point Reference 3.1.4 Temperature rise under several conditions3.1.5 Air purity C156-E142-02EN 3.2 Mounting Requirements 3.2.1 External dimensionsFigure 3.2 Dimensions Unit mm Note The height length is 25.4 ± 0.8 besides the panel sizeUnit mm Note Those enclosed in parentheses are inch screws Figure 3.3 Dimensions without panelC156-E142-02EN C156-E142-02EN 3.2.2 Installation directionFigure 3.4 Installation directions # Horizontal # Vertical Two orientationsC156-E142-02EN 3.2.3 Centers of gravityFigure 3.5 Centers of gravity Figure 3.5 shows the centers of gravity of the drive Unit mmFigure 3.6 Mounting frame structure 3.2.4 Notes on mounting∃15 orless Figure 3.7 Service clearance Figure 3.8 Current waveform +5 VDC 3.3 Power Supply RequirementsFigure 3.9 Connector and terminal locations 3.4 Cable Connections 3.4.1 Drive connectors3.4.3 Drive connection 3.4.2 Cable connector specificationsTable 3.3 Cable connector specifications Figure 3.10 Cable connection diagramCNH15 3.5 Jumper Settings 3.5.1 Jumper settings at factory shippingFigure 3.11 Jumper settings at factory shipping 3.5.2 Mode setting Figure 3.12 Master device settingFigure 3.14 Cable select mode setting Figure 3.13 Slave device settingCNH5CNH1 Figure 3.15 Cable select examples Device damage Use an antistatic mat and wrist strap when handling the drive3.6 Notes on Drive Handling 2 Do not leave the drive in dirty or contaminated environmentsDevice damage 3 InstallationMaster carton 12/24 units Figure 3.16 Individual packaging styleFigure 3.17 Gathered packaging style Eject Pin %2 Do not connect or disconnect any cable when the power is on 3.7.2 Mounting procedure3.7 Mounting 3.7.1 Checks before mounting the drive 1 Make sure that the system power is off3.9 Operation Confirmation and Preparation for Use after Installation 3.9.1 Confirming initial operationsThe BUSY LED is on while the optical disk drive is executing seek, write, or read operations. The BUSY LED is on momentarily, so it seems as if it blinked or is off 3.10 Dismounting Drive 3.9.2 Connection checkDevice damage CHAPTER 4 HOST INTERFACE 4.1 Pin Assignment 4.2 Signal Description 4.3 Interface Registers4.4 Various Processes 4.5 ATA Commands 4.6 Packet Commands 4.7 Timing Table 4.1 Differences in Host Interface Specifications of Each Model4.1 Pin Assignment Table 4.2 Connector pin assignments 1/2Table 4.2 Connector pin assignments 2/2 4.2 Signal Description Table 4.3 Signal description Table 4.4 I/O port functions and mapping 4.3 Interface Registers 4.3.1 I/O registers4.3.1.3 Data register 4.3.1.2 ATA Command register4.3.1.1 Alternate Status register Table 4.5 Bit definitions of Alternate Status registerTable 4.8 Bit definitions of ATAPI Byte Count register 4.3.1.5 Drive Address registerTable 4.7 Bit definitions of Drive Address register 4.3.1.6 ATAPI Byte Count registerTable 4.9 Bit definitions of ATAPI Block Device Select register 4.3.1.8 Error registerTable 4.10 Bit definitions of Error register 4.3.1.7 ATAPI Block Device Select register4.3.1.11 ATA Sector Count register 4.3.1.9 ATA Features register4.3.1.10 ATAPI Features register Table 4.11 Bit definitions of ATAPI Features registerTable 4.14 Bit definitions of ATAPI Status register Table 4.13 IO and Cod4.3.1.13 Sector Number register 4.3.1.14 ATAPI Status registerIn all other cases, the ODD does not set BSY b Within 400 ns of receiving a command when the DRQ bit is not sete During DMA transfer when the DRQ bit is not set CHECK bit of the Status register Error register Device/Head register4.4 Various Processes 4.4.1 Reset response 4.4.3 Automatic alternate sector assignment function 4.4.2 Defect sector managementTable 4.15 Alternate sector assignment criteria 4.4.4 Data error detection criteria 4.4.5.1 Data buffer 4.4.5 Cache function4.4.5.2 Read cache 4.4.5.3 MO write cache 4.4.6 Media status notification function 4.4.7 Power management function4.4.7.4 Idle mode 4.4.7.1 Power mode4.4.7.2 Active mode 4.4.7.3 Pre-idle modeFigure 4.1 Power mode 4.4.7.6 Sleep mode4.4.7.7 Standby timer 4.4.7.8 Power mode transitionTable 4.17 LED indications 4.4.8 LED Indicationscode 4.5 ATA CommandsTable 4.18 Command codes and parameters Protocol4.5.1 IDENTIFY PACKET DEVICE XA1 Table 4.19 IDENTIFY PACKET DEVICE commandTable 4.20 Device parameter information 1/5 Table 4.20 Device parameter information 2/5 Table 4.20 Device parameter information 3/5 Table 4.20 Device parameter information 4/5 Table 4.20 Device parameter information 5/5 Table 4.21 PACKET command4.5.2 PACKET XA0 Table 4.23 CHECK POWER MODE command 4.5.3 DEVICE RESETTable 4.22 DEVICE RESET command 4.5.4 CHECK POWER MODE X98/XE5When no device 1 is connected Table 4.24 Power mode indication4.5.5 EXECUTE DEVICE DIAGNOSTIC Table 4.25 EXECUTE DEVICE DIAGNOSTIC command4.5.6 GET MEDIA STATUS XDA When the ODD is deviceTable 4.27 GET MEDIA STATUS command Table 4.26 Self-diagnosis detailed codeTable 4.29 IDLE IMMEDIATE command Error register4.5.7 IDLE IMMEDIATE X95/XE1 4.5.8 NOP NOP command4.5.9 SERVICE XA2 Not supported SERVICE commandTable 4.32 SET FEATURES command 4.5.10 SET FEATURES XEFTable 4.33 FR register setting value Table 4.34 Transfer setting values in the SC register PRVENAB SLEEP commandTable 4.35 Cylinder High register 4.5.11 SLEEP X99/XE64.5.12 STANDBY IMMEDIATE X94/XE0 Table 4.37 STANDBY IMMEDIATE commandTable 4.38 Packet command codes and parameters 4.6 Packet CommandsERASE command 4.6.2 ERASE command4.6.1 Logical Unit Number Table 4.41 FORMAT UNIT parameter list 4.6.3 FORMAT UNIT command Table 4.40 FORMAT UNIT commandTable 4.42 Defect list header INQUIRY command 4.6.4 INQUIRY commandFormat descriptor Table 4.45 INQUIRY data Table 4.47 Mode parameters 4.6.5 MODE SELECT command Table 4.46 MODE SELECT commandTable 4.49 Mode parameter header Table 4.48 Mode parameter listPage descriptor Table 4.53 Default values for the drive operation mode page 4.6.5.1 Drive operation mode pageTable 4.51 Drive operation mode page Table 4.52 Changeable values in drive operation mode pageTable 4.54 Read-Write error recovery page 4.6.5.2 Read-Write error recovery pageTable 4.56 Default values for the read-write recovery page Table 4.55 Changeable values in the read-write recovery pageFlexible disk page 4.6.5.3Table 4.57 Flexible disk page Table 4.58 Changeable values in flexible disk page Table 4.59 Default values in flexible disk pageTable 4.61 Changeable values in the caching page Table 4.62 Default values for the cashing page4.6.5.4 Caching pageTable 4.63 Removable block access capabilities page 4.6.5.5 Removable block access capabilities pageTable 4.67 Inactivity Time Multiplier value 4.6.5.6 Timer & protect page Table 4.66 Timer & protect pageTable 4.69 Default values for the timer & protect page Table 4.68 Changeable values for the timer & protect pageTable 4.72 Mode parameter list 4.6.6 MODE SENSE command Table 4.70 MODE SENSE commandTable 4.71 Page Control field Page descriptor Table 4.73 Mode parameter headerTable 4.75 PREVENT/ALLOW MEDIUM REMOVAL command 4.6.7 PREVENT/ALLOW MEDIUM REMOVAL commandTable 4.76 Response to Prevent/Allow/Eject READ command 4.6.8 READ 10 commandREAD command 4.6.9 READ 12 commandTable 4.80 READ CAPACITY data PMI = 4.6.10 READ CAPACITY command Table 4.79 READ CAPACITY commandTable 4.81 READ CAPACITY data PMI = 1, MO media, FROM media Table 4.84 READ FORMAT CAPACITIES data format 4.6.11 READ FORMAT CAPACITIES commandTable 4.83 READ FORMAT CAPACITIES command Table 4.82 READ CAPACITY data PMI = 1, PROM mediaTable 4.86 Current/Maximum capacity descriptor 4.6.12 READ DEFECT DATA command Table 4.88 READ DEFECT DATA commandTable 4.87 Descriptor code definition Physical sector address format Table 4.89 Defect list formatsDefect descriptor Table 4.91 Defect list header4.6.14 RECEIVE DIAGNOSTIC RESULTS command 4.6.13 READ LONG command Table 4.92 READ LONG commandTable 4.93 RECEIVE DIAGNOSTIC RESULTS command REQUEST SENSE command 4.6.15 REQUEST SENSE commandTable 4.95 Request sense data Table 4.97 Sense key Table 4.96 Error codeTable 4.99 ASC/ASCQ list 1/2 Table 4.98 Logical block address formatSense Table 4.99 ASC/ASCQ list 2/2 Table 4.100 Format Progress Indication Bytes 4.6.16 SEND DIAGNOSTIC command Table 4.101 SEND DIAGNOSTIC command4.6.18 START/STOP UNIT command 4.6.17 SEEK command Table 4.102 SEEK commandSTART/STOP UNIT command Table 4.105 SYNCHRONIZE CACHE command 4.6.19 SYNCHRONIZE CACHE commandTable 4.104 START/STOP/EJECT processing 4.6.21 VERIFY command Table 4.107 VERIFY command 4.6.20 TEST UNIT READY command Table 4.106 TEST UNIT READY commandByteChk 4.6.23 WRITE 12 command Table 4.109 WRITE 12 command 4.6.22 WRITE 10 command Table 4.108 WRITE 10 command4.6.24 WRITE AND VERIFY command Table 4.110 WRITE AND VERIFY command Valid download data is Fujitsu distributed data only 4.6.25 WRITE BUFFER command Table 4.111 WRITE BUFFER commandTable 4.112 Code-ID Download procedure4.6.26 WRITE LONG command Table 4.113 WRITE LONG command DD150 t5 t6 4.7 Timing 4.7.1 Register/PIO data transfer timingFigure 4.2 Register/PIO data transfer t0 DA20 CS0-/CS1 t1 t2 t9 t2i DIOR-/DIOW WRITE DD150 t3 t4 READTable 4.114 Register/PIO data transfer timing parameters Figure 4.3 Multiword DMA data transfer 4.7.2 Multiword DMA data transfer timingTable 4.115 Multiword DMA data transfer timing parameters Figure 4.4 Power-on and reset timing 4.7.3 Power-on and Reset TimingTable 4.116 Power-on and reset timing 5.3 Optical Disk Cartridge Operation CHAPTER 5 OPERATION AND CLEANING5.1 Operating Optical Disk Drive 5.2 Cleaning Drive 5.4 Cleaning Optical Disk Cartridge5.1.3 Inserting cartridge 5.1.2 Note3 Insert the cartridge, shutter first, into the disk insertion slot 2 When the drive power is off1 Make sure that no optical disk cartridge is in the disk drive 2 Keep the cartridge shutter surface upward5.1.4 Ejecting removing cartridge Figure 5.2 Inserting cartridgePush the eject button Figure 5.3 Removing cartridgeC156-E142-02EN Device Damage 5.2 Cleaning DriveHead cleaner Be sure to use the dedicated head cleaner described above2. Shutter 1. Cartridge case 3. Write protect tab Shutter open 5.3 Optical Disk Cartridge Operation 5.3.1 Optical disk cartridgeFigure 5.4 Optial disk cartridge See Subsection 2.3.2 for the functions of the parts Shutter closedFigure 5.5 Write protect tab 5.3.2 Write protect tab5.4 Cleaning Optical Disk Cartridge 5.4.1 Cleaning toolCleaning kit 5.3.3 NotesSetting case Table 5.3 Packaged items cleaning kit5.4.2 Cleaning procedure Damage for data mediumDamage for disk medium Put a disposable groves at cleaning not put on the disk mediaFigure 5.6 Cleaning procedure Figure 5.7 Cleaning procedureIn case of contact with eyes, immediately flush eyes with water Figure 5.8 Cleaning procedureDamage for disk medium Eye inflammation7 Turn the revolving knob, then wipe the disk surface Cleaning cloth Figure 5.9 Cleaning procedureC156-E142-02EN 6.1 Diagnosis CHAPTER 6 DIAGNOSIS AND MAINTENANCE6.1 Diagnosis 6.2 Maintenance Information Table 6.1 Self-diagnostic function6.1.1 Initial self-diagnosis 6.1.2 Diagnostic command6.1.3 Test program Data loss 6.2 Maintenance Information 6.2.1 Maintenance requirementsFigure 6.1 Revision label 6.2.2 Revision numberFigure 6.2 Revision number indication Error correction code Axial displacementCDB Command Descriptor Block CommandSpindle Sense keyStatus Abbreviations Synchronous Data Transfer Request Index Page Page I, Place des Etas-Unis, SILIC 310, 94588 Rungis Cedex, FRANCE Reader Comment Form FUJITSU LIMITED