Indications, Alm | Furuno FS-1503 specs

[SCAN/6]	Turns the scan/sweep function on or off. “SCAN” or “SWEEP” appears on
	the display when the scan or sweep function is on.
[RX]	Selects an Rx frequency.
[TUNE/7]	Tunes the antenna coupler. “TUNE” appears during tuning, and “OK” appears
	after tuning is successfully completed.
[H/L /8]	Alternately selects high or low output power.
[ /9]	Adjusts backlighting of the keyboard and the display.
[CH]	Enables entry of channel (by ten key).
[2182]	Selects 2182 kHz on H3E (J3E may be selected depending on system setting).
[INT/0]	Calls “remote station” (if connected). Press this key, enter station no. and then
	press [ENT] key.
[ALM]	Releases the two-tone alarm for 45 seconds. To transmit the alarm, press the
	[ENT] key while holding down the [ALM] key. To silence it, press the [ENT/
	STOP] key or the [ALM] key. Never press [ALM] + [ENT] except when own
	ship is in distress.
[ENT]	Concludes data entry.
[0]...[9]	Enter numeric data.

Indications

The operation display provides the operational status by various marks and indications. Shown below are the location and meaning of all available indications. They do not appear all at once but when the related parts appear with respect to the mode selected.

Clarifier ON	* Rx channel	* Rx freq. or station name
	(Tx CH at Tx)	(Tx freq. at Tx)

					Transmit
								Low output power
	ITU channel								Antenna tuning
	selected								Antenna tuning
	selected				T				in progress
			ITU						in progress
			ITU
	Duplex	DUP CLAR							Antenna
	Simplex	DUP CLAR							tuning
	Simplex	SIMP TR							completed
									completed
	Tx output								Cursor
	Tx output	0	2	4	6	8 10 RF			Cursor
	(RF level)	0	2	4	6	8 10 RF			Loudspeaker OFF
	Tx output	0	1	2	3	4 5 ANTLOW TUNE OK SQ			Loudspeaker OFF
	Tx output	0	1	2	3	4 5 ANTLOW TUNE OK SQ			Squelch ON
	(antenna						AGC NB SWEEP SCAN		Scan ON
	current)					MEMO REM COM DUMMY
						LSB	J3E	H3E TLX FAX	Class of Emission
	TR: Tx, Rx freq.								Frequency Sweep ON
	R: Rx, freq.								Frequency Sweep ON
	R: Rx, freq.

	System setting mode		Noise
	User channel	Intercom ON	Noise
	User channel		Blanker	Dummy antenna in
	writing mode		Blanker	Dummy antenna in
	writing mode	AGC ON	ON	coupler ON
			ON	coupler ON

		Remote control
		ON

* Tx/Rx CH only or Tx/Rx freq. only available thru system setting.

Figure 1-3 Indications

1-3

Image 8

Furuno FS-1503 manual Indications, Alm

Contents

Page Page Safety Instructions Table of Contents Features Introduction System Configuration Operation Keys Transceiver Unit DescriptionRotary controls Indications ALM Turning the Power On/Off Adjusting the BacklightingTurning the Loudspeaker On/Off Turning the Squelch On/Off Selecting Frequency Turning AGC on/off Direct frequency entry Rx frequencyTx frequency Paired Rx/Tx frequency User channels J3E ITU telephony channels SSB Sample displays of ITU telephony channel ITU Telex channels TLX Transmitting Tuning the antennaDisplaying Station Name Using the microphone Monitoring transceiver output powerReducing transmitter power Distress Call on 2182 kHz Distress frequencies Distress calls and Distress message Adjusting RF gain Clarifier adjustmentReceiving Meter Noise blanker NB Receiving AM broadcasting stationsSquelch control User channels Frequency ScanChannel scan ITU channels 12 Sample scan screen Frequency Sweep MIF Commands MIF commands applicable to the FS-1503 Furuno Nbdp Terminal DP-5/DP-6 Operation of Optional EquipmentTelex Communication Remote Station RB-500 requires optional Remote-B Board IntercomPriority Communication on 2182 kHz Customizing by User Changing System SettingsSystem Setup Scan/sweep-stop signal level Writing User Channels Maintenance Aural testingTesting the transmitter with a dummy antenna Weekly Checks Diagnostic Test Sequence of diagnostic test LCD/Keyboard Test & ROM Version No. Confirmation Key and corresponding indication Maintenance Maintenance Maintenance con’t Troubleshooting Troubleshooting List Troubleshooting list con’t Errow Indication Replacing Fuses Specifications General Antenna Coupler Appendix Custom CHANNELS/FREQUENCIES MF band working carrier frequencies ref. US CFR 47 Part MF band SSB working carrier frequencies CH no MHz ITU SSB carrier frequencies ITU RR Appendix ITU CH no Following frequencies are factory programmed 12/16 MHz ITU SSB carrier frequencies ITU RR Appendix CH no Ship RX Ship TX Telex Channels MF Band Telex Frequency Table MHz Band ITU Nbdp Telex Frequency Table ITU RR Appendix 8001 12001 12/16 MHz Band ITU Nbdp Telex Frequency Table 16111 18/19 MHz Band ITU Nbdp Telex Frequency Table CH NO. Ship RX Ship TX 22001 22, 25/26 MHz Band ITU Nbdp Telex Frequency Table Index