Manuals / Furuno / Marine Equipment / Fish Finder

Furuno LS-6100 manual Operation, Control Description, Turning the Power On/Off, Display unit

Models: LS-6100

1 47

Download 47 pages 41.07 Kb

Page 8

Image 8

1. OPERATION

1.1 Control Description

How to remove the hard cover

Place your thumbs at the center of the cover, and then lift the cover while pressing it with your thumbs.

Display unit

1.2Turning the Power On/Off

Press the [POWER/BRILL] key more than one second to turn on the power. The unit beeps, the startup screen appears, and then the equipment checks the ROM and RAM for proper operation and displays program number. (If “NG” (No Good) appears, try to press any key except the [POWER/BRILL] key to start operation. However, the equipment may not work properly. Contact your dealer.) You may

Page 8

Image 8

Furuno LS-6100 manual Operation, Control Description, Turning the Power On/Off, How to remove the hard cover, Display unit

Contents

Echo Sounder 00080926502 Table of Contents Use the proper gain setting Do not open the equipmentDo not disassemble or modify the equipment Use the proper fuseSafety Instructions for the Installer Use the specified power cableFeatures ForewordWord to LS-6100 Owners IiiSystem configuration Equipment lists System OverviewStandard supply Name Type Code No Qty Remarks Optional equipment Name Type Code No Qty RemarksTurning the Power On/Off How to remove the hard coverOperation Control DescriptionAdjusting Display Contrast, Brilliance Brilliance/contrast adjustment windowMode selection window Choosing a Display, FrequencyMarker-zoom display Single frequency displayDual frequency display Bottom-zoom display Bottom-lock displayNav data displays Bottom-zoom displayMenu Operating Procedure Automatic OperationHow automatic operation works Choosing automatic operationChoosing the manual mode Manual OperationRange offset Gain offsetAdjusting the gain Choosing Picture Advance SpeedUnit Basic Range Shifting the rangeMeasuring Depth Scope DisplaySuppressing Interference Suppressing Low Level NoiseClutter appearance Forms of interferenceErasing Weak Echoes White LineWaypoints 49.6Setting destination waypoint Registering waypoint from the waypoint listUsing the Prog key Prog KeyEditing waypoints Erasing waypointsAlarms Alarm descriptionActivating an alarm Picture Color HueDepth, temperature, speed setting window Alarm menuAlarm options Fish level optionsSetting the Draft Resetting Trip DistanceHow the alarm works Gain CompensationNav data window and item displayable Setting Up Nav Data DisplaysNAV Data Setup window Nav data displays 30 00.065N130 00.574E System & Installation Menus Water temperature display wide, FSystem Menu System menusNav window water temperature and speed Installation Menu Installation menuWaas options window Clear memory displayBottom level display MAINTENANCE, Troubleshooting Troubleshooting DiagnosticsTroubleshooting table If… Then check …Test Pattern Test patternsThru-hull Mount Transducer InstallationDisplay Unit Thru-hull mount transducer mounting Dimensions millimeters Typical thru-hull mount transducer installationsAcceptable transducer mounting locations Suitable transducer mounting locationsTransom mount transducer Mounting locations Transom Mount TransducerConstruction of fairing block Tape Transom mount transducerInside-hull Transducer Pre-test for speed and temperature Optional TriducerFinal preparation Tools and materials neededInstallation of bracket Height required at mounting locationMounting location on single drive boat Positioning the templateAdjusting 10 11 transom angle TransomAngle Shim with Taper down Taper up Parallel Transom angleCable routing Attaching the sensor to the bracketAttaching the sensor to the bracket Optional Water Temperature/Speed Sensor WiringWater temperature/speed sensor Establishing the groundOptional equipment Pin arrangement on Nmea portWater temp/speed sensor Connection of converterFeeding data to RD-30 via the LS-6100 IEC 61162-1 Data SentencesWind sensor Specifications of the Echo Sounder LS-6100 Page