Garland 4522970 REV 1 INSTALLATION Continued, Rigid Connections, Flexible Couplings & Connectors

INSTALLATION Continued

Rigid Connections

Double-check any installer-supplied intake pipes visually and clear any dirt particles, threading chips, or other foreign matter before installing in a service line.. Those particles will clog orifices when gas pressure is applied..

Flexible Couplings & Connectors

If the unit is to be installed with flexible couplings and/or quick-disconnect fittings, for an appliance equipped with casters, the installation shall be made with a heavy duty, AGA design-certified commercial flexible connector or at least 3/4” NPT (with suitable strain relief) in compliance with the Standard for Connectors for Moveable Gas Appliances, ANSI Z21..69/CSA 6..16, Addenda Z21..69B-2006/CSA 6..16B-2006 (or latest edition), and a quick-disconnect device that complies with the Standard for Quick Disconnects for Use with Gas Fuel, ANSI Z21..41/CSA 6..9, Addenda Z21..41A-2005/CSA 6..16A-2005 (or latest edition), and adequate means must be provided to limit the movement of the appliance without depending on the connector and the quick-disconnect device or its associated piping to limit the appliance movement and the location(s) where the restraining means may be attached to the appliance shall be specified..

Further, if the unit is to be installed on a non-combustible surface that is equipped with casters, means must be provided to limit the movement of the unit with casters..

Manual Pilot Valve

Check all gas connections for leaks using a soapy solution before lighting any pilots! DO NOT USE AN OPEN FLAME TO CHECK FOR LEAKS! Putting an open flame beside a new connection is not only dangerous, but will often miss small leaks that a soapy solution would find..

All Garland appliances are adjusted and tested before leaving the factory, effectively matching them to sea level conditions.. Adjustments and calibrations to assure proper operation may be necessary on installation to meet local conditions, low gas pressure, differences in altitude, variations in gas characteristics, to correct possible problems caused by rough handling or vibration during shipment, and are to be performed only by qualified service personnel..

These adjustments are the responsibility of the customer, installer and/or dealer and are not covered by the Garland warranty..

All burners are equipped with continuous electronic spark electrodes to insure flame is on at all times during operation.. Continuous sparking is intended to remain energized until power is manually switched off..

WARNING:  All connections must be sealed with a joint compound suitable for LP gas, and all connections must be tested with a soapy solution before lighting any pilots!

Start Up

Before initial lighting or if unit does not operate at all check to see if:

1.Main gas supply shut off to appliance is open..

2.Electric power supply power and cord Nema 5-15P has been plug into an appropriate 120V 15Amp 60Hz outlet..

For daily start up:

1.Models HEEE-24CL and HEEE-36CL have one power switch.. Once pushed to the “ON” position an igniter supplies a continuous spark to the burners igniting the gas to all burners simultaneously.. At the same time the power switch opens up the gas flow to burners..

2.Models HEEE-48CL and HEEE-60CL have two power switches which operate in the same manner as the single switch above.. Each switch operates separately allowing the operator to run two sections of the broiler independently.. On the HEEE-48CL the switch on the far left operates burners 1 to 5.. The power switch on the right will operate burners 6 to 9.. On the HEEE-60CL the left switch controls burners 1 to 6 and the right switch controls burners 7 to 11..

3.If burners do not ignite, shutdown power to the unit, and wait 5 minutes before repeating ignition.. If repeated ignition fails, shutdown power to the unit and contact a service person..

4.Your broiler is an energy saving unit, all burners are pre- set at the factory to run at a consistent steady flame.. No adjustment should be attempted by the operator..

Shut Down

1.For shutting down overnight, on all models turn the power switch(es) to the “OFF” position..

Part # 4522970 Rev 1 (10/28/09) Page 7