Magnum 6K32 Managed Switch

Installation and User Guide (02/05)

2.2.3 Eight-Port Copper

1

3

5

7

Module, 6K8-RJ45

10/100

 

 

LK

 

 

 

The 6K32’s 8-port

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Copper port module, model 6K8-

F/ H

 

 

2

 

 

 

 

 

4

 

 

 

 

 

6

 

 

 

 

 

 

 

ACT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8

 

 

 

RJ45, provides eight 10/100Mb

10/100

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

switched RJ-45 ports. The

F/H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ACT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10/100Mb switched ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

normally (as a default setting) are independently N-way auto-negotiating for operation at 10 or 100Mb speed in full- or half-duplex mode, i.e., each independently selects a mode and speed to match the device at the other end of the twisted pair cable. (See Section 4.3 for auto-negotiation details)

On the model 6K8-RJ45 module, there are four LEDs for each port, two in the connector and two separate. The LK (Link) LED indicates “ready for operation” on that port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb speed when OFF (when auto-negotiation is not disabled). The FDX/HDX LED is ON to indicate full-duplex operation and OFF to indicate half-duplex mode. A twisted pair cable must be connected into an RJ-45 port and the Link (LK) indicator for that port must be ON (indicating there is a powered-up device at the other end of the cable) in order for a LK LED to provide valid indications of operating conditions on that port.

Using the MNS-6K software, the user may disable auto-negotiation and fix the desired operation of each RJ-45 port. MNS-6K Software allow to select 10Mb or 100Mb speed and full- or half-duplex mode per-port as per user requirement. (See Magnum MNS-6K Software Manual for details info). See Section 4.3 for Up-Link switch.

2.2.4Six-Port “4 + 2” Combo Modules, 4@ 10/100 RJ-45 and 2@ 100Mb fiber The combo six-port modules are combinations of copper and fiber media,

available as four 10/100 switched RJ-45 copper ports and two 100Mb switched multi-

 

1

 

3

5

7

 

10/100

 

 

 

 

 

LK

F/H

 

 

 

 

 

ACT

ACT

 

 

ACT

 

 

F/H

 

 

F/H

 

 

 

2

TX

LK RX

6

TX

LK

RX

4@ RJ-45 + 2@ 100Mb SC

 

1

 

3

5

7

 

10/100

 

 

 

 

 

LK

F/H

 

 

 

 

 

ACT

ACT

 

ACT

 

 

F/H

 

 

F/H

 

 

 

2

TX

LK RX

6

TX

LK

RX

 

4@ RJ-45 + 2@ 100Mb ST

www . GarrettCom . com

10

Page 16
Image 16
GarrettCom 6K32 manual Eight-Port Copper Module, 6K8-RJ45, @ RJ-45 + 2@ 100Mb SC, @ RJ-45 + 2@ 100Mb ST