GarrettCom DX40 1.4 Pinouts

CHAPTER 1 - Overview

Pinouts

DX40 Serial Device Router Installation Guide

1.4 Pinouts

The following subsections describe the pinouts of the connectors used with the DX40.

1.4.1 RJ45

Table1-8 defines the pinout of the RJ45 connector used with the DX40. RJ45 connectors

can be used on one of the Ethernet ports for 10/100 BaseT connections to copper

Ethernet-capable devices.

1.4.2 SFP

Table1-9 defines the pinout of the SFP connector used with the DX40. SFP connectors

are used on ports E1 and E2 for 100FX multi/single mode for connections to fiber optic

Ethernet-capable devices or networks.

Table1-8. RJ45 Pinout

Pin Signal

1 Tx +

2 Tx -

3 Rx +

4 not used

5 not used

6 Rx -

7 not used

8 not used

Pin 8 Pin 1

Table1-9. SFP Pinout

Port Signal

Tx Transmit

Rx Receive

E1/E2

Contents

Main Page i Declarations DOCUMENT NOTICE Copyright Rights Part Number Information W LIMITATION OF LIABILITY iii P RETURN OF EQUIPMENT COMPLIANCE NOTICES FCC Part 15 iv S v Service Personnel Warning Grounding CONTACTING GARRETTCOM UTILITY NETWORKS Page vii T Preface CHAPTER 1: OVERVIEW CHAPTER 2: INSTALLATION C viii Preface 8 ABOUT THIS MANUAL C RELATED DOCUMENTS WEB ACCESS YOUR COMMENTS Chapter 1 Overview 1.1 Overview 1.2 Configuration 1.2.1 Connectivity 1.2.2 Power and Ground 1.2.3 Indicators 1.2.4 Mounting Options 4 1.3 Specifications 1.3.1 Physical The physical dimensions and weight of the DX40 are defined in Tabl e 1-1. 1.3.2 Environmental The environmental specifications of the DX40 are defined in Table1-2. 1.3.4 Compliance The power requirements of the DX40 are defined in Table1-5. The industry compliance profile of the DX40 is defined in table Table1-4. 1.3.5 Power Requirements 6 8 The ports and external connectors of the DX40 are defined in Tabl e 1-6. 1.3.7 Indicators 1.4 Pinouts 1.4.1 RJ45 1.4.2 SFP 1.4.3 DB9 (Female) RS232 Serial Ports 1.4.4 DB9 (Female) RS485 Serial Ports Chapter 2 Installation 2.1 Preparing for Installation 2.1.1 Tools 2.1.2 Site Suitability 2.1.3 Wiring and Grounding Guidelines 2.1.4 Fiber Optic Safety 2.1.5 Fiber Optic Handling 2.1.6 External Connections 2.2 Unpacking 2.2.1 Attaching Optional Ethernet Fiber Optic SFPs 2.3 Installation of the DX40 Unit 2.3.1 Mounting 2.3.1.1 Mounting on a Panel 2.3.1.2 Mounting in a DIN Rail System 2.3.2 Connecting Facility Power 2.3.2.1 Making the Ground and Power Connections non-polarized ~ or Page 2.3.3 Connecting Network Cables 2.3.3.1 Connecting Serial Cables 2.3.3.2 Connecting Ethernet Copper Cables 2.3.3.3 Connecting Fiber Ethernet Cables 2.4 Maintenance 2.4.1 Removing the DX40 2.4.1.1 Disconnecting Network Cables 2.4.1.2 Disconnecting Power and Ground Lines 2.4.1.3 Packing the DX40 for Shipment 2.4.2 Cleaning Fiber Optic Devices 2.4.2.1 Cleaning Connectors 2.4.2.2 Cleaning Optical Ports