GBC ORCA-IV Figure 1-5:Locations of Safety Labels

Safety	ORCA-IV Image Transfer Laminator Operation Manual

One Located At

Each Roll Load

Point (7 Total)

Located

Inside

Cabinet

	WARNING	Located
		Inside
	ACHTUNG	Inside
	ACHTUNG	Cabinet
	MISE EN GARDE

CAUTION! EXPOSED ROLLER Can cause personal injury.

Keep hands, long hair, ties, jewelry and loose clothing away from this area.

Located Inside

©1994 Hazard Communication Systems, Inc. 800-748-0241

YST

O

P

A

A

TO

N

E

Cabinet

WARNING

ACHTUNG

MISE EN GARDE

On

Exterior

Panels

®

LISTED

Model No. Serial No. I.T.E

6N10

VAC

Hz®

Amps

Phase

Wires

MADE IN U.S.A.

WARNING

ACHTUNGMISEEN

GARDE

EmergencyKick or
StepStop
on toKick
Stop	Located
	Located	Below.
		Below.
	Process.

SEE INSTALLATION INSTRUCTIONS

BEFORE CONNECTING TO THE

SUPPLY

Emergency Stop Kick Cables Located Below.

Kick or Step on to Stop Laminating Process.

YST

O

P

A

A

T

ON

E

IV™

ORCA

4

SAFETY

INSTRUCTIONS

SICHERHEITSRICHTLINIEN

SÉCURITÉCONSIGNES -

-

©1994 Hazard Communication Systems, Inc. 800-748-0241

6 A

1 A

6 A

24VDC

6 A/250V 1/4 X 1-1/4 IN [ 5 X 20mm ]

1 A/250V 1/4 X 1-1/4 IN [ 5 X 20mm ]

CAUTION

FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,

REPLACE ONLY WITH SAME TYPE AND RATING OF FUSE

Located Inside Cabinet

Located Inside Cabinet

HIGH LEAKAGE CURRENT! Earth connection essential before connecting supply

Located On Door

	SAFETY
≤ 100 PSI	INSTRUCTIONS
≥ 700 KPa	SICHERHEITS-
©1997 HCS, Inc. 800-748-0241 No. 6101-52BVPK

	RICHTLINIEN
	CONSIGNES DE
	SÉCURITÉ

Figure 1-5: Locations of Safety Labels

1-6	© GBC Pro-Tech 1998 October

Contents

Part Number 930-009Rev. A GBC Pro-Tech 4151 Anderson Road De Forest, Wisconsin Tel: © GBC Pro-Tech1998 October 7DEOHRI&RQWHQWV ORCA-IVImage Transfer Laminator Operation Manual Cleaning Lubrication Exclusions to the Warranty 6HFWLRQ6DIHW ORCA-IVImage Transfer Laminator Operation Manual Kick Cable Reset Button Machine Reset Procedure 1.Make sure all emergency stop buttons and kick cables are reset Fig- ure Exercise care when cleaning the rolls with 80% (or stronger) isopropyl alcohol: ∙Use only in a well ventilated area ∙Wear rubber gloves ∙Use only on cool rolls &DXWLRQ:DUQLQJ/DEHO/RFDWLRQV Figure 1-5:Locations of Safety Labels Page Page 6HFWLRQ,QVWDOODWLRQ 3UHLQVWDOODWLRQ&KHFNOLVW The air supply to the laminator must be clean and dry or the machine will be damaged Page 8QSDFNLQJ 6HWXS /HYHOLQJ 6WDUWXS ❏Is the motor functioning Test the motor at various speeds ranging from 0-19ft/min (0-5.8m/min). At 0 the rolls should stop turning ❏Are the heaters working ❏Is the temperature set correctly Page 6HFWLRQ2SHUDWLRQ 6DIHW Page Table 3-1:Audible Signals Audible Signal Meaning 2SHUDWRU&RQWUROV ROLL TEMPERATURE 9.ROLL HEAT ON/OFF - Turns the heater control- ler for the top roll on or off ROLL HEAT ON/OFF PULL ROLL UP/DOWN COOLING FAN ON/OFF Figure 3-6:Front Brake Panel Page PULL ROLL PRESSURE DISPLAY MAIN ROLL UP/DOWN PULL ROLL PRESSURE CONTROL GBC LOGO AUTOMATIC/MANUAL MODE CONTROL SPEED/ACCUMULATOR DISPLAY 12.ACCUMULATOR RESET - Resets the accumu- lator Figure 3-8:Rear Brake Panel /RDGLQJWKH)LOP +HDWLQJ 5HFRPPHQGHG0DWHULDOV 6HWWLQJWKH6OLWWHU 3DSHU7LSV Page )LOP6SDFLQJ 2SHUDWLRQDO7LSVDQG7ULFNV 3URFHVV&RQWURO&KDUWV 9LQ\O7UDQVIHU 0DFKLQH6KXWGRZQ ORCA-IVImage Transfer Laminator Operation ManualOperation Notes Page 7URXEOHVKRRWLQJ &OHDQLQJ To clean beads of adhesive, dust and dirt from the rolls: Exercise care when cleaning the rolls with 80% isopropyl alcohol: Harsh chemicals like toluene, acetone or MEK destroy the silicone covering of the rolls /XEULFDWLRQ $GMXVWLQJWKH.LFN&DEOH &RQWDFWLQJ7HFKQLFDO6XSSRUW Figure 4-1:Grease Fittings 2XWSXW7URXEOHVKRRWLQJ*XLGH Possible Cause Corrective Action Number See "Machine Reset Procedure" on Problem Number Page Page Page Page 6HFWLRQ:DUUDQW /LPLWHG:DUUDQW Warranty 6HFWLRQ6SHFLILFDWLRQV Specifications ,QGH 1XPHULFV 1-1