Maintenance and Troubleshooting | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Problem | Problem |
| Possible Cause |
|
| Corrective Action |
Number |
|
|
| |||
|
|
|
|
|
| |
|
|
|
|
|
| |
12 | I pressed the motor forward | a. | Has a speed setting been set? | a. | Press the FWD or REV arrow and | |
| button, but the rolls would | b. Are the doors closed and shafts |
| turn the speed control up. | ||
|
| locked in? |
| b. | Close the doors and lock in the | |
| not turn! |
|
| |||
| c. | Are the |
| unwind/rewind shafts. | ||
|
|
| ||||
|
|
| Are the kick cables reset? |
| c. | Make sure all safety buttons are |
|
| d. Is there decimal on display? |
|
| released (out). Be sure all kick | |
|
| e. | Check motor fuses on the back of |
| cables are reset and adjusted | |
|
|
| machine. |
|
| properly. Press the machine reset |
|
|
|
|
|
| (above main switch). See |
|
|
|
|
|
| "Machine Reset Procedure" on |
|
|
|
|
|
| page |
|
|
|
|
|
| cable is truly resetting (listen, |
|
|
|
|
|
| look). Adjust the kick cable. See |
|
|
|
|
|
| “Adjusting the Kick Cable” on |
|
|
|
|
|
| page |
|
|
|
|
| d. | Press the machine reset (above |
|
|
|
|
|
| main switch). See "Machine |
|
|
|
|
|
| Reset Procedure" on page |
|
|
|
|
| e. | Remove fuses and replace, if nec- |
|
|
|
|
|
| essary. Be sure to replace with the |
|
|
|
|
|
| correct size fuses: two 6A fuses |
|
|
|
|
|
| for the motor and one 1A fuse for |
|
|
|
|
|
| the power supply. |
|
|
|
|
|
|
|
13 | I pressed the motor reverse | a. | see problem 12 |
| a. | See problem 12. |
| button, but the rolls would |
|
|
|
|
|
| not turn! |
|
|
|
|
|
|
|
|
|
|
|
|
14 | I pressed the main roll down | a. | Is there air pressure to the |
| a. | Verify that the air supply is suffi- |
| push button, but the roll did |
| machine? |
|
| ≤ |
| b. | Is there at least 20 psi on the |
|
| cient ( 100 psi). | |
| not go down! |
| b. | Turn up regulator for main roll | ||
|
|
| gauge? |
|
| pressure. |
|
| c. | Are the |
| c. | See problem 12. |
|
|
| pressed and the kick cables reset? | d. | See problem 12. | |
|
| d. | Is the machine reset? |
| e. | Reset the machine. See "Machine |
|
|
|
|
|
| Reset Procedure" on page |
|
|
|
|
|
|
|
15 | I pressed the main roll up | a. | Is there air pressure to the |
| a. | Verify that the air supply is suffi- |
| push button, but the rolls did |
| machine? |
|
| ≤ |
| b. | Is the machine reset? |
|
| cient ( 100 psi). | |
| not go up! |
| b. | Reset the machine. See "Machine | ||
|
|
|
|
|
| Reset Procedure" on page |
|
|
|
|
|
|
|
16 | I pressed the pull roll down | a. | Is there air pressure to the |
| a. | Verify that the air supply is suffi- |
| push button, but the rolls did |
| machine? |
|
| ≤ |
| b. | Is there at least 20 psi on the |
|
| cient ( 100 psi). | |
| not go down! |
| b. | Increase the pull roll air pressure. | ||
|
|
| gauge? |
| c. | Disconnect and reconnect air |
|
| c. Is the roll hook retracted? |
|
| pressure to the machine and | |
|
| d. Are the |
|
| observe pull roll locking mecha- | |
|
|
| pressed and the kick cables reset? |
| nism. | |
|
| e. | Is the machine reset? |
| d. | See problem 12. |
|
|
|
|
| e. | Reset the machine. See "Machine |
|
|
|
|
|
| Reset Procedure" on page |
|
|
|
|
|
|
|
© GBC |