Manuals / Brands / Computer Equipment / Laminator / GBC / Computer Equipment / Laminator

GBC ORCA-IV set-point, ROLL TEMPERATURE, ROLL HEAT ON/OFF, PULL ROLL UP/DOWN, COOLING FAN ON/OFF, PREHEATER HEAT ON/OFF, SPEED/ACCUMULATOR TOGGLE

1 56

Download 56 pages, 1.08 Mb

ORCA-IV Image Transfer Laminator Operation Manual	Operation

8.ROLL TEMPERATURE - Provides a readout of the temperature of the upper main roll and the set- point for the desired temperature adjustment. Press the star button on the temperature controller to see or change the set point.

9.ROLL HEAT ON/OFF - Turns the heater control- ler for the top roll on or off.

10.PULL ROLL UP/DOWN - Sets the pull roll to the up (load) or down (operate) position.

11.COOLING FAN ON/OFF - Turns the cooling fan on or off. Push once to turn only the cooling idlers on, push again to turn only the cooling tubes on, push a third time to turn both cooling idlers and cooling tubes on, and push a fourth time for all cooling off.

12.PREHEATER AIR TEMPERATURE (optional) - Provides a readout of the temperature of the air inside the preheater and the set-point for the desired temperature.

13.PREHEATER HEAT ON/OFF - Turns the heater controller in the preheater roll on or off.

14.ACCUMULATOR RESET - Resets the accumu- lator.

15.SPEED/ACCUMULATOR TOGGLE - Toggles control between the speed and the accumulator.

16.MOTION CONTROL FORWARD/STOP/ REVERSE - Controls the direction of the drive system, forward, reverse, or stop.

© GBC Pro-Tech 1998 October

3-5

Contents

Part Number 930-009Rev. A GBC Pro-Tech 4151 Anderson Road De Forest, Wisconsin Tel: © GBC Pro-Tech1998 October 7DEOHRI&RQWHQWV ORCA-IVImage Transfer Laminator Operation Manual Cleaning Lubrication Exclusions to the Warranty 6HFWLRQ6DIHW ORCA-IVImage Transfer Laminator Operation Manual Kick Cable Reset Button Machine Reset Procedure 1.Make sure all emergency stop buttons and kick cables are reset Fig- ure Exercise care when cleaning the rolls with 80% (or stronger) isopropyl alcohol: ∙Use only in a well ventilated area ∙Wear rubber gloves ∙Use only on cool rolls &DXWLRQ:DUQLQJ/DEHO/RFDWLRQV Figure 1-5:Locations of Safety Labels Page Page 6HFWLRQ,QVWDOODWLRQ 3UHLQVWDOODWLRQ&KHFNOLVW The air supply to the laminator must be clean and dry or the machine will be damaged Page 8QSDFNLQJ 6HWXS /HYHOLQJ 6WDUWXS ❏Is the motor functioning Test the motor at various speeds ranging from 0-19ft/min (0-5.8m/min). At 0 the rolls should stop turning ❏Are the heaters working ❏Is the temperature set correctly Page 6HFWLRQ2SHUDWLRQ 6DIHW Page Table 3-1:Audible Signals Audible Signal Meaning 2SHUDWRU&RQWUROV ROLL TEMPERATURE 9.ROLL HEAT ON/OFF - Turns the heater control- ler for the top roll on or off ROLL HEAT ON/OFF PULL ROLL UP/DOWN COOLING FAN ON/OFF Figure 3-6:Front Brake Panel Page PULL ROLL PRESSURE DISPLAY MAIN ROLL UP/DOWN PULL ROLL PRESSURE CONTROL GBC LOGO AUTOMATIC/MANUAL MODE CONTROL SPEED/ACCUMULATOR DISPLAY 12.ACCUMULATOR RESET - Resets the accumu- lator Figure 3-8:Rear Brake Panel /RDGLQJWKH)LOP +HDWLQJ 5HFRPPHQGHG0DWHULDOV 6HWWLQJWKH6OLWWHU 3DSHU7LSV Page )LOP6SDFLQJ 2SHUDWLRQDO7LSVDQG7ULFNV 3URFHVV&RQWURO&KDUWV 9LQ\O7UDQVIHU 0DFKLQH6KXWGRZQ ORCA-IVImage Transfer Laminator Operation ManualOperation Notes Page 7URXEOHVKRRWLQJ &OHDQLQJ To clean beads of adhesive, dust and dirt from the rolls: Exercise care when cleaning the rolls with 80% isopropyl alcohol: Harsh chemicals like toluene, acetone or MEK destroy the silicone covering of the rolls /XEULFDWLRQ $GMXVWLQJWKH.LFN&DEOH &RQWDFWLQJ7HFKQLFDO6XSSRUW Figure 4-1:Grease Fittings 2XWSXW7URXEOHVKRRWLQJ*XLGH Possible Cause Corrective Action Number See "Machine Reset Procedure" on Problem Number Page Page Page Page 6HFWLRQ:DUUDQW /LPLWHG:DUUDQW Warranty 6HFWLRQ6SHFLILFDWLRQV Specifications ,QGH 1XPHULFV 1-1