GEAppliances.com

SPEED CYCLE 7.5 gal., 35–70 min.(on some models) This cycle is for everyday dishes and glassware.

RINSE ONLY

2.5 gal., 10 min.

 

For rinsing partial loads that will be washed later. Do not use detergent with this cycle.

NOTE: This dishwasheris equippedwith a CleanSensor™ withautomatictemperaturecontrol; therefore, cycle length and time may vary depending on soil and temperature conditions.

NOTE: Onlythe SANI WASHcycle has been designed to meet the requirements of Section6, NSF 184 for soil removal and sanitization efficacy.

 

 

Options

 

4

 

 

 

The light above the selected pad will be ON to indicate which ENHANCEMENT/EXTRA has been selected.

 

 

 

 

 

 

STEAM

For use with heavily soiled and/or dried-on,baked-onsoils. This option MUSTbe selectedPRIOR

 

(on some models) to starting the cycle. The STEAM optionadds24 minutesto the cycletime.

 

 

 

 

 

 

HEATED DRY

When HEATED DRY is off, dishes will air dry.

 

 

Light OFF

 

 

 

 

 

 

 

HEATED DRY

Turns the heater on for faster drying. This will extend the total cycle time between

 

 

Light ON

8 and 38 minutes depending on the cycle selected. NOTE: HEATED DRY cannot be

 

 

 

selected with RINSE ONLY cycle.

 

 

 

 

 

 

LOCK

You can lock the controls to prevent any selections from being made. Or you can lock

 

 

 

the controls after you have started a cycle.

 

 

 

Children cannot accidentally start dishwasher by touching pads with this option

 

 

 

selected.

 

 

 

To unlock the dishwasher controls, touch and hold the HEATED DRY pad for 3

 

 

 

seconds. The light above the LOCK pad will turn off. To lock the dishwasher control,

 

 

 

touch and hold the HEATED DRY pad for 3 seconds. The light above the LOCK pad

 

 

 

will turn on.

 

 

 

 

 

 

ADDED HEAT

When selected, the cycle will run with heating element on longer and may increase

 

 

 

cycle times to improve both wash and dry performance.

 

 

 

NOTE: Cannot be selected with RINSE ONLY cycle.

 

 

 

 

 

 

DELAY HOURS

You can delay the start of a wash cycle for up to 9 hours. Touch the DELAY HOURS pad

 

 

 

to choose the number of hours you want to delay the start of the cycle; then touch

 

 

 

START/RESET. The machine will count down and start automatically at the correct time.

 

 

 

Touching START/RESET a second time will cancel the DELAY START selection.

 

 

 

NOTE: If you forget to fully close the door, a reminder signal will beep until you do so.

 

 

 

 

 

 

RESET

To change a cycle after washing starts, touch the START/RESET pad to cancel the

 

 

 

cycle. The START/RESET light will flash while the water is pumped out if needed. This

 

 

 

takes approximately 90 seconds. When the light stops flashing, the dishwasher

 

 

 

can be reprogrammed and restarted.
5 START

Close the dishwasherdoorand selectthe cycleand desiredenhancements.Touch the START/RESET pad to beginthe cycle. Water fill begins, and approximately 60 secondslaterthe washaction begins.

NOTE: The dishwasherremembersyourlast cycleso you don’thaveto reprogrameachtime. Whenthe dishwasherdoor is fully closed,the control panellights will displaythe lastsettingsyou selected.

If you don’t wantto changeany of the settings,simply touchthe START/RESET pad to beginthe cycle.

If the door is closed,the indicatorlightswill turnoff if the START/RESETpad is not selected within two minutes.To activate the display,openand close the door or pressany pad.

Also, if a powerfailure occurs,NORMAL WASH and HEATEDDRY will automaticallybe programmed.Make any new selections and touchthe START/RESET pad to beginthe cycle.

6 CLEAN

The CLEAN light will illuminate and a doublebeepwill soundwhena washcycleis complete. On somemodels,the CLEAN light will turn off whenthe door is opened.On other models, the CLEAN lightwill remain on until the door is opened

and thenrelatchedor until any keypadis pressedwhile the door is latchedshut.

11

Instructions Safety

Instructions Operating

Tips Troubleshooting

Support Consumer