![INSTALL AND CONNECT THE CASE](/images/new-backgrounds/35942/3594239x1.webp)
Installation Instructions
INSTALL AND CONNECT THE CASE
1.Remove the front case panel and pull
the unit out of the case. Place the empty case onto the platform in the closet with the outdoor side facing the wall plenum opening. Align the case with plenum opening and attach with six
2.Adjust all four leveling legs until the case is level.
Inside
wallRigid ductwork
5a INSTALL AND GROUND
THE UNIT TO THE CASE
UNIT INSTALLED THROUGH FRONT OF CASE
1.Slide the back of the unit into the case. Push the unit all of the way into the case until it stops.
NOTE: Either of the case sides may be removed to enable the unit to be slid into the case.
2.Ground the unit to the case by installing the front
Air discharge outlet
Leveling legs
3.Using
4.Connect the internal or external drain(s) as necessary.
Secondary 3⁄4” drain option. If not used, seal with a MNPT plug
Primary female drain fitting 3⁄4”
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| External |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| drain |
NOTE: Piping is not |
| Bolt case |
|
|
|
|
| OR | ||||||||||
|
|
|
|
|
| Internal | ||||||||||||
supplied with the unit. | to platform |
|
|
|
|
| ||||||||||||
|
|
|
|
| drain(s) | |||||||||||||
Obtain locally. |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
Side screw
|
|
|
|
| Hex bolt |
Side screw |
| |
|
| |
|
|
|
INSTALL AND GROUND
THE UNIT TO THE CASE
UNIT INSTALLED THROUGH SIDE OF CASE
1.Slide the side of the unit into the case. Push the unit all of the way into the case until it stops.
NOTE: Either of the case sides may be removed to enable the unit to be slid into the case.
2.Attach the case side panel to the main case.
3.Ground the unit to the case by installing the front
| Side screw |
Side screw |
|
| |
(may be |
|
installed on |
|
either side) | Hex bolt |
|
20