Before you begin — Read these instructions completely and carefully. IMPORTANT - Save these instructions for local inspector’s use.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer - Be sure to leave these instructions with the Consumer.
Note to Consumer - Keep these instructions with your Use and Care Book for future reference.
WARNING: This appliance must be properly grounded. See “Electrical Supply,” page 4
If you have a question concerning the installa- tion of this product, call the GE Answer Center® Consumer Information Service at 800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged vent hood, you should immediately contact your dealer or builder.
For Monogram local service in your area, 1-800-444-1845.
For Monogram service in Canada, call 1-888-880-3030.
For Monogram Parts and Accessories, call 1-800-626-2002.
CAUTION!
Due to the weight and size of this vent hood and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Use & Care Guide for warranty information.
WARNING:
To reduce the risk of fire or electrical shock, do not use this hood with any external solid- state speed control device. Any such alteration from original factory wiring could result in damage to the unit and/or create an electrical safety hazard.
To reduce the risk of fire and to properly exhaust air, be sure to duct air outdoors. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
WARNING; TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
TO REDUCE THE RISK OF FIRE, ELECTRI- CAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If you have any ques- tions, contact the manufacturer.
B. Before servicing or cleaning unit, switch power off at the service panel and lock service panel to prevent power from being switched on accidentally. If the service panel cannot be locked, fasten a tag or prominent warning label to the panel.
For general ventilating use only. Do not use to exhaust hazardous or explosive materials or vapors.
Structural framing, installation work and electrical wiring must be done by qualified person(s), in accordance with all applicable codes and standards including
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrig- eration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
Local codes vary. Installation electrical con- nections and grounding must comply with applicable codes. In the absence of local codes, the vent should be installed in accor- dance with National Electrical Code ANSI/ NFPA
Contents
Models available | 3 |
Required Accessory | 3 |
Product Dimensions | 3 |
Tools and Materials Required | 4 |
Power Supply | 4 |
Duct Fittings | 5 |
Installation Preparation |
|
Step 1, Advance Planning | 6, 7 |
Installation |
|
Step 2, Remove the Packaging | 8 |
Step 3, Check Installation Hardware | 8 |
Step 4, Mount Template | 9 |
Step 5, Install Support Frame | 9 |
Step 6, Secure Wiring | 10 |
Step 7, Size and Install Ductwork | 10 |
Step 8, Install Decorative Duct Covers | 11 |
Step 9, Install Hood | 12 |
Step 10, Connect Electrical | 12 |
Step 11, Slide Duct Cover Down, |
|
Install Utility Bars | 13 |
Step 12, Install Filters | 14 |
Step 13, Finalize Installation | 14 |
2
