Genicom P45 user manual

Models: P45

1 115
Download 115 pages 31.78 Kb
Page 114
Image 114

114

 

POST (hex)

 

Debug Code Action

 

BIOS Program Definition

 

Possible Cause

 

Solution

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

75

 

Power on

-

 

Initializing storage devices.

1.

Lost power source of some devices.

1.

Inspect the power cable connection.

 

 

> Stopped at 75

 

 

 

 

 

 

 

 

(Probing for IDE devices or SATA

 

 

 

 

 

 

 

 

 

 

2.

Incompatible SATA or PATA

2.

Inspect the IDE cable connection or

 

 

 

 

 

 

 

devices)

 

 

 

 

 

 

 

 

 

device.

 

replace another PATA/ SATA device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

CD-ROM’s spin took too long.

3.

Remove the disc, if present, from the

 

 

 

 

 

 

 

 

 

 

 

CD-ROM device.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7F

 

Power on

-

 

BIOS setup module in progress.

1.

Checksum error occured.

1.

Load the optimized default setting

 

 

 

> Stopped at 7F

 

 

 

 

 

* Checksum error always

 

Reporting BIOS check errors.

 

(Change/add devices such as CPU/

 

of the BIOS.

 

 

 

 

 

 

DRAM)

 

 

 

 

 

 

appear after the BIOS default

 

 

 

 

 

 

 

 

 

 

 

Waiting for keys:

2.

Error occured after clearing the

2.

Alter or adjust the BIOS setting.

 

 

 

 

has been loaded.

 

 

 

 

 

 

 

 

DEL key to load the BIOS default.

 

CMOS.

 

 

 

 

 

 

 

 

 

F1 key to continue.

 

 

 

 

 

 

 

 

 

 

 

3.

Onboard battery is depleted.

3.

Replace a new battery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

Overclocking issue.

4.

Decrease the overclock range.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

* The battery circuit of the MB is

* RMA action required.

 

 

 

 

 

 

 

 

 

defective.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FF

 

Power on

-

 

Boot attempt (INT 19h)

Normal Operation

Nil

 

 

 

> Run to FF

 

 

 

 

 

* Blank Screen

 

System booted normally.

* The graphics card was not

* Remove and reinstall the graphics

 

 

 

 

 

 

 

 

 

connected properly or it is defective.

 

card.

 

A

Debug LED POST and Troubleshooting

Page 114
Image 114
Genicom P45 user manual