|
| Troubleshooting | |
|
|
| |
Problem | Cause | Solution | |
|
|
| |
|
|
| |
Pump does not prime. | In Immersion Mode suction tube is | Make sure suction tube is immersed | |
| not immersed | in paint. | |
|
|
| |
| Suction tube is leaking. | Tighten suction tube connection. | |
|
| Inspect for cracks or vacuum leaks. | |
|
|
| |
| Pump does not prime with fluid. | Remove suction tube from paint. | |
|
| Prime pump with water or sol- | |
|
| ||
|
|
| |
Spray gun stopped spraying. | Spray tip is clogged. | Unclog spray tip, page 14. | |
|
|
| |
Pump cycles but does not build up | Pump is not primed. | Prime pump. | |
pressure. |
|
| |
Inlet screen is clogged. | Clean debris off inlet screen. | ||
| |||
|
|
| |
| In Immersion Mode suction tube is | Make sure suction tube is immersed | |
| not immersed in paint. | in paint. | |
|
|
| |
| Hopper or paint pail is empty. | Refill hopper or paint pail. Reprime | |
|
| sprayer. | |
|
|
| |
| Suction tube is leaking. | Tighten suction tube connection. | |
|
| Inspect for cracks or vacuum leaks. If | |
|
| cracked or damaged, replace suction | |
|
| tube. | |
|
|
| |
Pump cycles, but paint only dribbles | Pressure is set too low. | Slowly turn AllControl to Hi Spray to | |
or spurts when spray gun is trig- |
| increase pressure setting. | |
gered. |
|
| |
Spray tip is clogged. | Unclog spray tip, page 14. | ||
| |||
|
|
| |
| Spray gun fluid filter is clogged. | Clean or replace gun fluid filter. | |
|
|
| |
| Spray tip is too large or worn. | Replace tip. | |
|
|
| |
Spray pattern is inconsistent or is | Pressure is set too low. | Slowly turn AllControl to HI SPRAY to | |
leaving stripes. |
| increase pressure setting. | |
|
|
| |
| Spray tip is worn beyond capability of | Replace spray tip. | |
| sprayer. |
| |
|
|
| |
| Paint is too thick. | Thin paint slightly with compatible | |
|
| solvent or water. | |
|
|
| |
Pressure is set at maximum but can- | Spray tip is too large for sprayer. | Select smaller spray tip. | |
not achieve a good spray pattern. |
|
| |
Spray tip is worn beyond capability of | Replace spray tip. | ||
| |||
| sprayer. |
| |
|
|
| |
| Extension cord is too long or not | Replace extension cord. Grounding | |
| heavy enough gauge. | and Electrical Requirements, page 4. | |
|
|
| |
| Spray gun fluid filter is clogged. | Clean or replace spray gun fluid filter. | |
|
|
| |
| Inlet screen is clogged. | Clean debris off inlet screen. | |
|
|
| |
When paint is sprayed, it runs down | Coat is going on too thick. | Move gun faster. | |
the wall or sags. |
|
| |
| Choose a tip with smaller hole size. | ||
|
| ||
|
|
| |
|
| Choose tip with wider fan. | |
|
|
| |
|
| Make sure gun is far enough from | |
|
| surface. | |
|
|
| |
When paint is sprayed, coat is not | Coat is going on too thin. | Move gun slower. | |
covering. |
|
| |
| Choose tip with larger hole size. | ||
|
| ||
|
|
| |
|
| Choose tip with narrower fan. | |
|
|
|
32 | 312079A |
