Inventory, Crate Contents Qty | Grizzly G0609 guide

Inventory

After all the parts have been removed from the wood crate, you should have the following items:

Crate Contents: (Figure 3 & 4)		Qty
A.	Jointer Assembly	1
B.	Fence Assembly	1
C.	Fence Bracket	1
D.	Push Blocks	2
E.	Knife Setting Jig	1

E

C

B

D

A

Figure 3. Crate contents.
Hardware and Tools	Qty
• Hex Wrenches 3, 4, 8, 10mm	1 Each
• Open End Wrench
10/12, 12/14,17/19mm	1 Each
• Cap Screws M12-1.75 x 30 (Fence)	2
• Flat Washers 12mm (Fence)	3
• Lock Washers 12mm (Fence)	2
• Lock Nut M12-1.75 (Fence)	1
• Flat Washers 10mm (Pedestal)	2
• Lock Washers 10mm (Pedestal)	2
• Cap Screws M10-1.5 x 25 (Pedestal)	........ 2

-12-

Figure 4. Additional crate contents.

In the event that any nonproprietary parts are missing (e.g. a nut or a washer), we would be glad to replace them, or for the sake of expedi- ency, replacements can be obtained at your local hardware store.

NOTICE

Some hardware/fasteners on the inventory list may arrive pre-installed on the machine. Check these locations before assuming that any items from the inventory list are miss- ing.

SUFFOCATION HAZARD!

Immediately discard all plas- tic bags and packing materi- als to eliminate choking/suf- focation hazards for children and animals.

G0609 12" Parallelogram Jointer

Image 14

Grizzly G0609 owner manual Inventory, Crate Contents Qty, Hardware and Tools Qty

Contents

Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Contact Info IntroductionForeword Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram Jointer G0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit Requirements Items Needed for Set Up SET UPSet Up Safety Unpacking Hardware and Tools Qty Crate Contents QtyInventory Hardware Recognition Chart Site Considerations Clean UpMachine Placement Floor Load Bolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointer Fence is Heavy To install the fenceFence Winding Cutterhead Guard Pedestal SwitchTo set up the pedestal switch Components and Hardware Needed Qty To check the outfeed table height Knife Setting JigChecking Outfeed Table Height To test run the machine Dust Port Test RunRecommended CFM at Dust Port ... CFM Operation Safety Basic Controls Operations Stock Inspection and Requirements Correct and incorrect grain alignment Minimum dimensions for edge Jointing Squaring Stock Surface Planing To surface plane on the jointer Edge Jointing To edge joint on the jointer Bevel Cutting To bevel cut on the jointer Rabbet Cutting To rabbet cut on the jointer G3631-Jointer/Planer Knife Hone AccessoriesH9291-12 Shellix Spiral Cutterhead H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSS Grizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736 Schedule MaintenanceCleaning Unpainted Cast Iron Maintenance Log Date Approximate Hours Of Use Maintenance Performed Motor & Electrical ServiceTroubleshooting Cutting Tools Needed Qty Adjusting/Replacing KnivesInspecting Knives To inspect the knives Cutterhead profile diagram To adjust/replace the knivesPage To check the outfeed table parallelism Checking/Adjusting Table ParallelismChecking Outfeed Table Checking Infeed Table Adjusting Table ParallelismTo adjust the table parallelism To check the infeed table parallelism Setting Outfeed Table Height To set the outfeed table height Setting Infeed Table Scale Setting Fence StopsCalibrating Depth To calibrate the depth scale To set the 90˚ fence stop To set the 45 outward fence stop To align the pulleys Belts Pulley AlignmentTo replace the V-belts Page G0609 Electrical Components Motor junction box G0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List Description Table Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page