Manuals / Grizzly / Power Tools / Biscuit Joiner

Grizzly G0609 owner manual Operations, Operation Safety Basic Controls

Models: G0609

1 60

Download 60 pages 13.02 Kb

Page 22

SECTION 4: OPERATIONS

Operation Safety		Basic Controls

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

This section covers the basic controls used during routine operations.

START Button: Starts motor only if the STOP button is in the out position (Figure 16).

STOP Button: Stops motor when pushed in and disables the START button. Enable the START button by twisting the STOP button until it springs forward in the out position.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving machinery.

NOTICE

If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

-20-

STOP		START
Button		Button

Figure 16. START/STOP button locations.

G0609 12" Parallelogram Jointer

Image 22

Grizzly G0609 owner manual Operations, Operation Safety Basic Controls

Contents

Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsItems Needed for Set Up SET UPSet Up Safety UnpackingInventory Crate Contents QtyHardware and Tools Qty Hardware Recognition Chart Site Considerations Clean UpMachine Placement Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerFence To install the fenceFence is Heavy Winding Cutterhead Guard Pedestal SwitchTo set up the pedestal switch Components and Hardware Needed QtyChecking Outfeed Table Height Knife Setting JigTo check the outfeed table height Recommended CFM at Dust Port ... CFM Dust Port Test RunTo test run the machine Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9291-12 Shellix Spiral Cutterhead H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Schedule MaintenanceCleaning Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedTroubleshooting ServiceMotor & Electrical Cutting Tools Needed Qty Adjusting/Replacing KnivesInspecting Knives To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage Checking Outfeed Table Checking/Adjusting Table ParallelismTo check the outfeed table parallelism Checking Infeed Table Adjusting Table ParallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Scale Setting Fence StopsCalibrating Depth To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopTo replace the V-belts Belts Pulley AlignmentTo align the pulleys Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page