Manuals / Grizzly / Power Tools / Biscuit Joiner

Grizzly G0609 owner manual Squaring Stock, Minimum dimensions for edge Jointing

Models: G0609

1 60

Download 60 pages 13.02 Kb

Page 24

•Remove foreign objects from the stock. Make sure that any stock you process with the jointer is clean and free of any dirt, nails, staples, tiny rocks or any other foreign objects that may damage the jointer blades.

•Only process natural wood fiber through your jointer. Never joint MDF, particle board, plywood, laminates or other synthetically made materials.

•Make sure all stock is sufficiently dried before jointing. Wood with a moisture con- tent over 20% will cause unnecessary wear on the knives and poor cutting results.

•Make sure your workpiece exceeds the minimum dimension requirements (Figures 20 & 21) before edge jointing or surface planing, or it may break or kick back during the operation!

Squaring Stock

Squaring stock involves four steps performed in the order below:

1.Surface Plane On The Jointer—The con- cave face of the workpiece is surface planed flat with the jointer.

2.Surface Plane On a Thickness Planer—The opposite face of the workpiece is surface planed

flat with a thickness planer.

10" Min.

1" Min.

1⁄2" Min.

Figure 20. Minimum dimensions for edge

jointing.

Previously

Surface

Planed Face

3.Edge Joint On The Jointer—The concave edge of the workpiece is jointed flat with the jointer.

10" Min.

1⁄2" Min.

1" Min.

Figure 21. Minimum dimensions for surface

planing.

4.Rip Cut On A Table Saw—The jointed edge of the workpiece is placed against a table saw fence and the opposite edge cut off.

Previously

Jointed Edge

��

��

��

-22-	G0609 12" Parallelogram Jointer

Image 24

Grizzly G0609 owner manual Squaring Stock, Minimum dimensions for edge Jointing

Contents

Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsSET UP Set Up SafetyItems Needed for Set Up UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Clean Up Machine PlacementSite Considerations Floor LoadMoving & Placing Jointer Mounting to Shop FloorBolting to Concrete Floors To lift the jointerTo install the fence FenceFence is Heavy Pedestal Switch To set up the pedestal switchWinding Cutterhead Guard Components and Hardware Needed QtyKnife Setting Jig Checking Outfeed Table HeightTo check the outfeed table height Dust Port Test Run Recommended CFM at Dust Port ... CFMTo test run the machine Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerAccessories H9291-12 Shellix Spiral CutterheadG3631-Jointer/Planer Knife Hone H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Maintenance CleaningSchedule Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService TroubleshootingMotor & Electrical Cutting Adjusting/Replacing Knives Inspecting KnivesTools Needed Qty To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage Checking/Adjusting Table Parallelism Checking Outfeed TableTo check the outfeed table parallelism Adjusting Table Parallelism To adjust the table parallelismChecking Infeed Table To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Setting Fence Stops Calibrating DepthScale To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopBelts Pulley Alignment To replace the V-beltsTo align the pulleys Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page