Manuals / Grizzly / Power Tools / Biscuit Joiner

Grizzly G0609 owner manual Fence is Heavy, To install the fence

Models: G0609

1 60

Download 60 pages 13.02 Kb

Page 18

Fence

Make sure the fence, carriage, and table have been thoroughly cleaned of all the export grease before installing the fence, or the fence will not slide easily. The fence has a keyway slot built into the underside of it that fits over the key on the table. These keep the fence perpendicular to the cutterhead during adjustments.

The	fence is	heavy.
Seek	assistance	when
lifting it onto the jointer
stand.
Components and Hardware Needed:		Qty
Cap Screws M12-1.75 x 30	...............................	2
Flat Washers 12mm		3
Lock Washers 12mm		2
Lock Nut M12-1.75		1
Fence Bracket		1
Fence Assembly		1

To install the fence:

1.Align the mounting holes on the fence bracket and jointer, and fasten with the M12-1.75 x 30 cap screws, flat washers and lock washers as shown in Figure 8.

Figure 8. Installing fence bracket.

2.With the help of an assistant, lift the fence assembly over the fence bracket, slip the sliding bushing (Figure 9) into the fence bracket slot, and make sure the key and key- way slot fit snugly.

	Fence
Bracket Slot
Key	Sliding
Key Slot	Bushing

Figure 9. Installing fence assembly.

3.Secure the sliding bushing with a 12mm flat washer and lock nut.

-16-	G0609 12" Parallelogram Jointer

Image 18

Grizzly G0609 owner manual Fence is Heavy, To install the fence

Contents

Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Introduction ForewordContact Info Machine Data Sheet Capacity Identification Safety G0609 12 Parallelogram JointerG0609 12 Parallelogram Jointer Additional Safety for Jointers 220V Single-Phase Circuit RequirementsItems Needed for Set Up SET UPSet Up Safety UnpackingCrate Contents Qty InventoryHardware and Tools Qty Hardware Recognition Chart Site Considerations Clean UpMachine Placement Floor LoadBolting to Concrete Floors Moving & Placing JointerMounting to Shop Floor To lift the jointerTo install the fence FenceFence is Heavy Winding Cutterhead Guard Pedestal SwitchTo set up the pedestal switch Components and Hardware Needed QtyKnife Setting Jig Checking Outfeed Table HeightTo check the outfeed table height Dust Port Test Run Recommended CFM at Dust Port ... CFMTo test run the machine Operation Safety Basic Controls OperationsStock Inspection and Requirements Correct and incorrect grain alignmentMinimum dimensions for edge Jointing Squaring StockSurface Planing To surface plane on the jointerEdge Jointing To edge joint on the jointerBevel Cutting To bevel cut on the jointerRabbet Cutting To rabbet cut on the jointerG3631-Jointer/Planer Knife Hone AccessoriesH9291-12 Shellix Spiral Cutterhead H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSSGrizzly Dial Calipers Our most popular safety glasses H1300 H1298 G7984 H2347 H0736Schedule MaintenanceCleaning Unpainted Cast IronMaintenance Log Date Approximate Hours Of Use Maintenance PerformedService TroubleshootingMotor & Electrical Cutting Tools Needed Qty Adjusting/Replacing KnivesInspecting Knives To inspect the knivesCutterhead profile diagram To adjust/replace the knivesPage Checking/Adjusting Table Parallelism Checking Outfeed TableTo check the outfeed table parallelism Checking Infeed Table Adjusting Table ParallelismTo adjust the table parallelism To check the infeed table parallelismSetting Outfeed Table Height To set the outfeed table heightSetting Infeed Table Scale Setting Fence StopsCalibrating Depth To calibrate the depth scaleTo set the 90˚ fence stop To set the 45 outward fence stopBelts Pulley Alignment To replace the V-beltsTo align the pulleys Page G0609 Electrical Components Motor junction boxG0609 Wiring Diagram Base Assembly Parts Breakdown Base Parts List DescriptionTable Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page