Calibrating Depth, Scale, Setting Fence Stops | Grizzly G0609

Calibrating Depth
Scale
The depth scale on the infeed table can be cali-
brated or "zeroed" if it is not correct.
Tools Needed	Qty
Straightedge	1
Phillips Screwdriver	1
Wrench 17mm	1
Hex Wrench 5mm	1
To calibrate the depth scale:

1.DISCONNECT JOINTER FROM POWER SOURCE!

2.Loosen the infeed table positive stop bolts.

3.Use the straightedge to help adjust the infeed table exactly even with the outfeed table, as shown in Figure 55.

��

Figure 55. Infeed table even with outfeed table.

4.Using a screwdriver, adjust the scale pointer to "0" (Figure 56), then reset the infeed table positive stops.

Figure 56. Depth scale adjusted to “0” position. G0609 12" Parallelogram Jointer

Setting Fence Stops

The fence stops simplify the task of adjusting the fence to 45˚ inward, 90˚, and 45˚ outward (135˚).

Tools Needed	Qty
45° Square	1
90° Square	1
Sliding Bevel	1
Wrench 14mm	1
To set the 45˚ inward fence stop:

1.Tilt the fence approximately 45° inward (Figure 57) onto the positive stop bolts using a square.

Figure 57. Fence adjusted 45˚ inward.

2.Loosen the jam nut on the 45° inward positive stop bolt shown in Figure 58.

Jam Nut

45° Inward

Positive Stop

Bolt

Figure 58. 45° inward positive stop bolt (one of two shown).

3.Adjust the positive stop bolts until the fence is exactly 45° inward while resting on the bolts (verify the angle with a 45° square).

4.Retighten the jam nut loosened in Step 2.

-41-

Image 43

Grizzly G0609 owner manual Calibrating Depth, Scale, Setting Fence Stops, To calibrate the depth scale

Contents

Model G0609 Parallelogram Jointer Page Table of Contents Warranty and Returns Foreword IntroductionContact Info Machine Data Sheet Capacity Identification G0609 12 Parallelogram Jointer Safety G0609 12 Parallelogram Jointer Additional Safety for Jointers Circuit Requirements 220V Single-Phase Unpacking SET UPSet Up Safety Items Needed for Set Up Inventory Crate Contents QtyHardware and Tools Qty Hardware Recognition Chart Floor Load Clean UpMachine Placement Site Considerations To lift the jointer Moving & Placing JointerMounting to Shop Floor Bolting to Concrete Floors Fence To install the fenceFence is Heavy Components and Hardware Needed Qty Pedestal SwitchTo set up the pedestal switch Winding Cutterhead Guard Checking Outfeed Table Height Knife Setting JigTo check the outfeed table height Recommended CFM at Dust Port ... CFM Dust Port Test RunTo test run the machine Operations Operation Safety Basic Controls Correct and incorrect grain alignment Stock Inspection and Requirements Squaring Stock Minimum dimensions for edge Jointing To surface plane on the jointer Surface Planing To edge joint on the jointer Edge Jointing To bevel cut on the jointer Bevel Cutting To rabbet cut on the jointer Rabbet Cutting H2404-Jointer PalMagnetic Knife Jig Up to 12 Carbide or HSS AccessoriesH9291-12 Shellix Spiral Cutterhead G3631-Jointer/Planer Knife Hone Grizzly Dial Calipers H1300 H1298 G7984 H2347 H0736 Our most popular safety glasses Unpainted Cast Iron MaintenanceCleaning Schedule Date Approximate Hours Of Use Maintenance Performed Maintenance Log Troubleshooting ServiceMotor & Electrical Cutting To inspect the knives Adjusting/Replacing KnivesInspecting Knives Tools Needed Qty To adjust/replace the knives Cutterhead profile diagramPage Checking Outfeed Table Checking/Adjusting Table ParallelismTo check the outfeed table parallelism To check the infeed table parallelism Adjusting Table ParallelismTo adjust the table parallelism Checking Infeed Table To set the outfeed table height Setting Outfeed Table Height Setting Infeed Table To calibrate the depth scale Setting Fence StopsCalibrating Depth Scale To set the 45 outward fence stop To set the 90˚ fence stop To replace the V-belts Belts Pulley AlignmentTo align the pulleys Page Motor junction box G0609 Electrical Components G0609 Wiring Diagram Base Assembly Parts Breakdown Description Base Parts List Table Assembly Parts Breakdown Table Parts List Fence Assembly Parts Breakdown Fence Parts List Stand Assembly Parts Breakdown Stand Parts List 413 412 411 402403 401 410 404 405 406 409 407 408 Warranty and Returns Page Page