Harman-Kardon AVR 147 owner manual System Configuration

System Configuration

speakers are used, a subwoofer is required to reproduce low-frequency sounds. Remember that the “large” and “small” descriptions do not refer to the actual physical size of the speakers, but to their ability to reproduce low-frequency sounds. If you are in doubt as to which category describes your speakers, consult the specifications in the speakers’ owner’s manual, or ask your dealer.

At last, this menu also makes you chose if the speaker setting will be the same for each input source (GLOBAL), or will be set differently for each input (INDEPENDENT).

Notes:

•When "Independent" is selected for the speak- er settings (see below), they need to be made for each input individually and you can deter- mine which speaker should be used depending on the input source selected. So it´s possible e.g. to turn off the Center and/or the Sub with any music source selected and to use them with any movie input source.

•With the currently selected input all speaker settings will be copied to all other surround modes (as far as speakers are used with them) and need not be repeated when another sur- round mode is selected with that input.

It is easiest to enter the proper settings for the speaker setup through the SPEAKER SIZE menu (Figure 9). So press the OSD Button L to bring up the MASTER MENU (Figure 1), and then press the ¤ Button D three times so that the cursor is on the MANUAL SETUP line.

At this point, press the Set Button F and select the SPEAKER SIZE menu (Figure 9).

Figure 9

1.Before you start the speaker setting, you should determine if you want all inputs being configured with the same speaker size setting (GLOBAL) or if all inputs should be configured individually (INDEPENDENT).

To configure all inputs for "Global" or "Inde- pendent" press the ⁄ Button D twice so that the cursor is next to the BASS MGR line.

This setting allows you to use the same speaker configuration for all inputs, or to have different settings for each input. In most cases the factory default setting of GLOBAL will be appropriate, as most listeners do not need to have

individualized speaker settings. However, some listeners, particularly those with full-range front speakers that are used for both movies and music may prefer that different speaker settings be used when listening to music through a CD player as opposed to a movie from a DVD player, VCR or cable/satellite set top.

If you wish to customize the speaker size individ- ually to each input, make certain that the cursor is on the BASS MGR line and press the ‹/› Buttons E so that INDEPENDENT appears in highlighted video. When this setting is entered all speaker size settings will be shown with their factory default size in the menu and all other inputs will turn to INDEPENDENT too. Now you should enter the speaker size settings prefered for the input selected, as described below. Remember that in this case the size settings just entered will apply to the current input ONLY, and you will need to go back to the INPUT menu to select another input, and then return to this menu page again to change the settings for the next input. Repeat the procedure for any input where you wish to have a set of speaker configuration different from the default settings.

NOTE: When the INDEPENDENT setting is activated, you may assign different speaker size settings to each input to accommodate different bass management settings that match your preferences with the type of program material normally used with a particular source (for example, when movies are played from DVD and music from a CD player). However, the actual speaker crossover settings are set only once and do not change with the input selection. The reason is that, while bass management preferences may vary, the actual speakers remain the same, regardless of the bass-management and redirection settings.

2.Begin the speaker size setup process by making certain that the cursor is pointing toward the LEFT/RIGHT line, which sets the configura- tion for the front left and right speakers. If you wish to make a change to the front speakers’

configuration, press the ‹ / › Buttons E so that either LARGE or SMALL appears, match- ing the appropriate description from the definitions shown above.

When SMALL is selected, low-frequency front channel sounds will be sent only to the subwoofer output. If you choose this option and there is no subwoofer connected, you will not hear any low- frequency sounds with front channel signals.

When LARGE is selected, a full-range output will be sent to the front left and front right outputs. Depending on the choice made in the SUBWOOFER line in this menu (see below), the front left and right bass information may also be directed to the subwoofer.

NOTE: When the front speakers are set to the LARGE option and the surround mode is set to "Surround Off", or pure two-channel stereo, when an analog signal source is present it will be routed directly from the input to the volume control without being digitized or processed. If you have full-range front speakers and wish to remove all digital processing from the circuit path, select this configuration. If you wish to set this option for use with only one input, such as a CD player that uses an external DAC or an optional, external phono preamp, you must choose the INDEPENDENT setting on the BASS MGR line at the bottom of this menu so that only those inputs where the analog bypass is desired will be routed in this fashion, while other analog inputs such as a VCR or cable box will be digitized for surround processing.

Important Note: When a speaker set with a subwoofer and two front satellites connected to the Sub´s speaker outputs is used, the Sub´s inputs must be connected to the Front speaker outputs ￿ and LARGE must be selected for the front speakers (and NONE for the sub- woofer, see below).

3.When you have completed your selection for the front channel, press the ¤ Button D on the remote to move the cursor to CENTER.

4. Press the ‹/› Buttons E on the remote to select the option that best describes your center speaker, based on the speaker definitions shown below.

When SMALL is selected, low-frequency center channel sounds will be sent to the Fronts, if they are set to LARGE and Sub is turned off (see be- low). When Sub is on, low frequency center channel sounds will be sent to the subwoofer only.

When LARGE is selected, a full-range output will be sent to the center speaker output, and NO center channel signal will be sent to the sub- woofer output (except when the Pro Logic II Music mode is in use).

NOTE: If you choose Logic 7 as the surround mode for the particular input source for which you are configuring your speakers, the AVR will not make the LARGE option available for the center speaker. This is due to the requirements of Logic 7 processing, and does not indicate a problem with your receiver.

When NONE is selected, no signals will be sent to the center-channel output. The receiver will operate in a “phantom” center channel mode. Center-channel information will be sent to the left and right front channel outputs and the cen- ter channel bass will be sent to the subwoofer output when L/R+LFE is selected in the SUBWOOFER line in this menu (see below). This mode is needed if no Center speaker is used. Note that when the Logic 7 Cinema or Enhanced

24SYSTEM CONFIGURATION