3100 Wood Stove Series (ACC) |
| R | ||
|
| |||
|
| Mobile Home Installation |
|
|
| must use a |
|
| |
You6 |
|
|
| |
| SparkArestor Cap | |||
Part |
|
| ||
home. |
|
|
| |
1. | An outside air inlet must be provided for combustion See | Storm Collar |
| |
| page 14 for installation information. |
| ||
|
|
| ||
2. | Appliance must be secured to the mobile home structure |
| Roof Flashing | |
| by bolting the pedestal through hearth pad and into |
|
| |
| floor. |
|
|
|
3. | Appliance must be grounded with #8 solid copper |
|
| |
| grounding wire or equivalent and terminated at each end | Joist Shield/Firestop | Double wall | |
| with N.E.C. approved grounding device. | |||
|
| |||
4. | Appliance must be installed with an approved UL103 HT |
| connector pipe | |
|
| |||
| ventilated chimney connector, UL103 HT chimney, and |
|
| |
| terminal cap with spark arrestor. Never use a single wall |
|
| |
| connector (stove pipe) in a mobile home installation. Use |
|
| |
| only |
|
| |
| metalbestos DS or Security DL |
|
| |
| any listed |
|
| |
5. | In Canada, this appliance must be connected to a 6 inch |
| OutsideAir | |
| (152mm) |
| RearVent | |
| 629M, STANDARD FOR FACTORY BUILT CHIMNEYS. |
|
| |
6. | Follow the chimney and chimney connector manufacturer’s | Floor Protector |
| |
| instructions when installing the flue system for use in a |
| ||
|
|
| ||
| mobile home. |
|
| |
7. | Maintain clearance to combustibles. |
|
| |
8. | Floor protection requirements must be followed | Outside Air Floor Vent |
| |
| precisely. |
| ||
|
|
| ||
9. | Use silicone to create an effective vapor barrier at the | Figure 20.1 |
| |
| location where the chimney or other component penetrates |
| ||
|
|
| ||
| to the exterior of the structure. |
|
| |
NOTE: Offsets from the vertical, not exceeding 45°, are | CAUTION | |
allowed per Section 905(a) of the Uniform Mechanical Code | ||
(UMC). Offsets greater than 45° are considered horizontal | Maintain structural integrity of mobile home: | |
and are also allowed, providing the horizontal run does not | ||
• Floor, wall, ceiling and/or roof. | ||
exceed 75% of the vertical height of the vent. Construction, | ||
Do NOT cut through: | ||
clearance and termination must be in compliance with the | ||
• Floor joist, wall, studs or ceiling trusses. | ||
UMC Table 9C. This installation must also comply with NFPA | ||
• Any supporting material that would affect the structural | ||
211. | ||
integrity. | ||
NOTE: Top sections of chimney must be removable to allow | ||
| ||
| ||
maximum clearance of 13.5 feet (411cm) from ground level |
| |
for transportation purposes. |
| |
WARNING | ||
10. Burn wood only. Other types of fuels may generate | ||
poisonous gases (e.g., carbon monoxide). |
| |
Asphyxiation Risk. | ||
11. If unit burns poorly while an exhaust blower is on in | ||
• Never install in a sleeping room. | ||
home, (i.e., range hood), increase combustion air. | ||
Consumes oxygen in the room. | ||
|
12.Installation shall be in accordance with the Manufacturers Home & Safety Standard (HUD) CFR 3280, Part 24.
Page 20 |
| September 1, 2008 |
