Installing Wall Shield Firestops and Horizontal Termination Cap (SL Series Pipe ONLY)

WARNING

Fire Risk

Exhaust Fumes Risk

Impaired Performance of Appliance

Ensure vent components are locked together correctly.

Pipe may separate if not properly joined.

ForHorizontalRuns-WallshieldfirestopsareREQUIREDon bothsidesofacombustiblewallthroughwhichtheventpasses.

NOTE: Model SLK-01TRD does not need an exterior wall shield firestop on an exterior combustible wall.

To install wall shield firestops for horizontal runs that pass through either interior or exterior walls:

Cut a 10 in. x 10 in. (254mm x 254mm) hole for SL-D- series pipe. The center of the framing hole is one (1) inch (25.4mm) above the center of the horizontal vent pipe.

Position the wall shield firestops on both sides of the hole previously cut and secure the wall shield firestops with nails or screws.

The heat shields of the wall shield firestops MUST BE placed towards the top of the hole.

Continue the vent run through the wall shield firestops.

WARNING

Fire Risk. Explosion Risk.

Do NOT pack insulation or other combustibles between firestops.

ALWAYS maintain specified clearances around venting and firestop systems.

Install firestops as specified.

Failure to keep insulation or other material away from vent pipe may cause fire.

Installing the Horizontal Termination Cap

Vent termination must not be recessed in the wall. Siding may be brought to the edge of the cap base.

Flash and seal as appropriate for siding material at out side edges of cap.

When installing a horizontal termination cap, follow the cap location guidelines as prescribed by current ANSI Z223.1 and CAN/CGA-B149installation codes.

10 in. (254mm)

1 in. (25.4 mm)

10 in. (254mm)

VENT PIPE

Figure 8.14 Hole and Vent Pipe

HEAT SHIELD

TRIM HEAT SHIELD IF TOO LONG, ADD TO SHIELD IF TOO SHORT

WALL SHIELD

FIRESTOP

(EXTERIOR)

WALLSHIELD

FIRESTOP (INTERIOR)

WARNING

Burn Risk

• Local codes may require installation of a cap shield to prevent anything or anyone from touching the hot cap.

WARNING

Do NOT connect a pipe section to a termination cap without using the telescoping flue section found on the termination cap.

NOTE: Where required, an exterior wall flashing is available. When penetrating a brick wall, a brick extension kit is avail- able for framing the brick.

Figure 8.15 Heat Shield, Interior & Exterior Firestops

32

Hearth & Home Technologies • BE-36-C, BE-36-CIPI397-981 Rev. V 1/07

Page 32
Image 32
Hearth and Home Technologies BE-36-C manual Fire Risk. Explosion Risk

BE-36-C specifications

Hearth and Home Technologies, a leader in innovative heating solutions, offers two remarkable gas fireplaces: the BE-36-CIPI and BE-36-C. Both models are designed to deliver efficient heating, aesthetic charm, and user-friendly features, making them ideal for modern living spaces.

The BE-36-CIPI is a direct vent fireplace that provides the warmth of a traditional fire without the hassle of wood. One of its most notable features is its contemporary design, featuring clean lines and a wide viewing area. This model comes with an impressive heat output, ensuring that spaces remain comfortably warm during chilly seasons. The BE-36-CIPI incorporates innovative technologies like the IntelliFire™ ignition system, which promotes energy efficiency by providing reliable performance while minimizing fuel consumption.

Moreover, the fireplace's advanced burner system creates a stunning flame pattern and realistic look, enhancing the ambiance of any room. With customizable options, homeowners can choose different media types, such as ceramic logs or contemporary stones, allowing for personal expression in their décor.

On the other hand, the BE-36-C model offers similar features but with its unique twist. This model is characterized by its traditional aesthetic appeal, making it an excellent choice for those who prefer a classic look with modern convenience. The BE-36-C also utilizes the IntelliFire™ system, ensuring efficiency and ease of use. With a versatile design, this fireplace can fit into various style preferences, from rustic to modern.

Both models come equipped with optional heat management systems, allowing for effective temperature regulation. This feature is particularly useful for maintaining a comfortable environment without overheating the space. The fireplaces are also designed with safety in mind, adhering to strict safety standards and offering numerous safety features like a safety pilot and tempered glass doors.

In conclusion, Hearth and Home Technologies’ BE-36-CIPI and BE-36-C gas fireplaces present an ideal blend of aesthetics, efficiency, and advanced technology. Whether opting for the contemporary style of the BE-36-CIPI or the classic allure of the BE-36-C, homeowners are guaranteed to enjoy a superior heating experience that complements their home’s design while providing warmth and comfort.