Hearth and Home Technologies BE-36-C Pipe Length/Inches

59Hearth & Home Technologies • BE-36-C, BE-36-CIPI • 397-981 Rev. V 1/07

B. Vent Components Diagrams (continued)

Pipe Length/Inches

SL-06D 5-3/4

SL-09D 8-3/4

SL-12D 11-3/4

SL-12/17D 11-3/4 to 16-3/4

SL-17/24D 16-3/4 to 23-3/4

SL-24D 23-3/4

SL-36D 35-3/4

SL-48D 47-3/4

SL-FLEX-2 24

SL-FLEX-3 36

SL-FLEX-5 60

SL-FLEX-10 120

Theremust be a 25% reduction

intotal H when using the snor kel

capexcept when using the

simpleup and out installation.

6-1/2in.

(SL-SERIES)

WALL BRACKET

Figure 16.6 SL Series Vent Components

Contents

Main Models: BE-36-C BE-36-CIPI Owners Manual DO NOT DISCARD Congratulations Listing Label Information/Location NA Type of Gas We recommend that you record the following pertinent information about your appliance. - Table of Contents - Listing and Code Approvals C. BTU Speci cations A. Appliance Certi cation B. Glass Speci cations D. High Altitude Installations G. Requirements for the Commonwealth of Massachusetts A. Design and Installation Considerations Getting Started C. Inspect Appliance and Components B. Tools and Supplies Needed 3 A. Selecting Appliance Location B. Constructing the Appliance Chase C. Clearances D. Mantel Projections A. Vent Termination Minimum Clearances (See Figure 4.4 for speci c clearances) Measure horizontal clearances from this surface. Termination Locations Measure vertical clearances from this surface. Figure 4.2 speci es minimum vent heights for various pitched roofs. V = VENT TERMINAL X Alcove Applications 5 A. Vent Table Key 8-1/2 in. V C. Measuring Standards Horizontal D. Use of Flex Vent E. Vent Diagrams Two Elbows H H V 1. Top Vent - Horizontal Termination One Elbow H V V1 = 44 ft. Max. (13.4 m) CAP SIDE VIEW V Top Vent - Vertical Termination No Elbows Baf e Instruction 2. Top Vent - Vertical Termination - (continued) Three Elbows V H H V Page Two elbows 3. Rear Vent - Horizontal Termination- Three elbows V H V H One elbow 3. Rear Vent - Horizontal Termination Two elbows H V Three elbows B. Wall Penetration Framing Figure 6.1 Pipe Clearances Vent Clearances and Framing NOTE: Slope not required. Figure 6.2 Horizontal Venting Clearances to Combustible Materials ABCD BE-36-C in. 36 1/2 24 3/8 35 1/2 23 3/8 mm 927 619 902 594 C. Vertical Penetration Framing A. Choosing the Top or Rear Vent Appliance Preparation B. Rear Vent C. Securing and Leveling the Appliance A. Assembly of Vent Sections (DVP Pipe ONLY) Installing Vent Pipe A B Page B. Disassembly of Vent Sections (DVP Pipe ONLY) Assembly of Vent Sections (SL Series Pipe ONLY) C. Installing Heat Shield and Horizontal Termination Cap (DVP Pipe ONLY) WARNING WARNING Installing Wall Shield Firestops and Horizontal Termination Cap (SL Series Pipe ONLY) WARNING WARNING D. Installing Roof Flashing and Vertical Termination Cap Page A. Fuel Conversions B. Gas Pressures C. Gas Connection Gas Information HIGH ALTITUDE INSTALLATIONS Electrical Information B. Connecting to the Appliance A. Recommendation for Wire D. Intelli re Ignition System Wiring C. Standing Pilot Ignition System Wiring E. Junction Box Installation F. Wall Switch Installation for Fan (Optional) A. Mantel Projections B. Facing Material Finishing Appliance Setup A. Remove Shipping Materials B. Clean the Appliance C. Accessories Page E. Glass Assembly F. Grilles and Trim Operating Instructions CAUTION A. Before Lighting Appliance B. Lighting Appliance LIGHTING INSTRUCTIONS (IPI) CAUTION: NOT FOR USE WITH SOLID FUEL WARNING: DO NOT CONNECT 110 VAC TO THE CONTROL VALVE. Standing Pilot Ignition CAUTION: NOT FOR USE WITH SOLID FUEL WARNING: C. After Appliance is Lit D. Frequently Asked Questions A. Standing Pilot Ignition System Troubleshooting Troubleshooting (continued) Symptom Possible Cause Corrective Action B. Intelli re Ignition System Sympton Possible Cause Corrective Action Intelli re Ignition System - (continued) Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials A. Appliance Dimension Diagram B. Vent Components Diagrams UP Figure 16.2 DVP vent components DVP45 (45 Elb ow) Page 13-1/4 in. (367 mm) 24-5/8 in. (625 mm) 27-1/2 in. (127 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (367 mm) RF12M Roof Flashing Multi-pak DRC-RADIUS Cap Shield 13-7/8 in. (352 mm) 7-1/4 in. (184 mm) 5-1/4 in. (133 mm) 12-1/2 in. (318 mm) DVP-TVHW VerticalTermination Cap (Highwind) Pipe Length/Inches BE-36-C AVAILABLE TO SHIP IN 24 HOURS ITEM DESCRIPTION SERIAL # PART NUMBER Additional service part numbers may appear on the following page. Standing Pilot BE-36-C C. Service Parts List Service Parts BE-36-C Standing Pilot Valve Assembly Service Parts BE-36-CIPI IPI Valve Assembly AVAILABLE TO SHIP IN 24 HOURS ITEM DESCRIPTION SERIAL # PART NUMBER LIMITED LIFETIME WARRANTY D. Limited Lifetime Warranty