Tools and Supplies Needed | Hearth and Home Technologies EXCLAIM-36

F. Tools and Supplies Needed

Before beginning the installation be sure the following tools and building supplies are available:

Reciprocating saw	Framing material
Pliers	Non-combustible sealant
Hammer	Gloves
Phillips screwdriver	Framing square
Flat blade screwdriver	Electric drill and bits
Plumb line	Safety glasses
Level	Tape measure

1/2-3/4 in. length, #6 or #8 self-drilling screws Misc. screws and nails

G. Fireplace System Requirements

This ﬁreplace system requires:

•Hearth Refractory

•Grate Assembly

•Outside Air Hood

- Duct must be installed, but sold separately.

H. Inspect Fireplace and Components

WARNING! Risk of Fire and/or Explosion! Damaged parts could impair safe operation. DO NOT install dam- aged, incomplete or substitute components. Keep ﬁre- place dry.

•Remove ﬁreplace and components from packaging (please refer to Section 7) and inspect for damage.

•Vent system components and doors are shipped in separate packages.

•Report to your dealer any parts damaged in shipment.

•Read all the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and beneﬁt.

Heat & Glo • EXCLAIM-36, EXCLAIM-42 • 4013-251 Rev C • 11/08

17

Image 17

Hearth and Home Technologies EXCLAIM-36 owner manual Tools and Supplies Needed, Fireplace System Requirements

Contents

Fire Risk Wood Burning FireplaceHot screen/mesh and glass doors will cause burns Number Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Heat & Glo EXCLAIM-36, EXCLAIM-42 4013-251 Rev C 11/08 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible Materials Hot glass will cause burns Operating InstructionsYour Fireplace Starting a Fire Seasoned WoodGrate Firescreen Vented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear Space Wood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for Removal Check Firebox Refractory Glass CleaningInspect Grate Frequency As desired Start Fire Problems Possible Cause Solution Troubleshooting Guide Typical Fireplace System Getting Started Negative Pressure Design and Installation ConsiderationsDraft Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Inspect Fireplace and Components Tools and Supplies NeededFireplace System Requirements Select Fireplace Location Framing & Clearances Clearances to Combustible Materials Clearances Frame the Fireplace Sidewalls/Surrounds Unpack the Fireplace EXCLAIM-42 only Installation of FireplaceThings to Consider Unpack the Fireplace EXCLAIM-36 only Removing Smoke Shield Position the Fireplace EXCLAIM-42 only GAS Knockout Install the Refractory EXCLAIM-42 only Level Fireplace Place Protective Metal Hearth Strips YES Install Outside Air Kit Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air Kit Installing the Ceiling Firestop Install Ceiling Firestops 330 mm Install Attic Insulation Shield Install Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in Roof Flat Roofs Chimney Termination Requirements Construct the Chase Chase Installations Install Chase Top Install Fireplace & Chimney ST1175/ST475 Square Termination Cap Install Termination Cap TCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shield Roofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension Hearth Extension Construction Raised Hearth Extension Framing Flush Hearth Extension Framing Non-combustible Sealant Noncombustible Facing Finishing Material Combustible Mantel 19 3/4 502 mm Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1 Reference Materials Fireplace Dimensions EXCLAIM-36 EXCLAIM-42 Catalog # Chimney Components 15-1/4 387 mm 15-3/4 400 mm CT56 Chase Top LDS33/LDS46 Decorative Shroud EXCLAIM-36H, EXCLAIM-36T Service Parts EXCLAIM-42H, EXCLAIM-42T This page intentionally left blank Do not Discard this Manual