TCT1175 Terra Cotta Cap | Hearth and Home Technologies EXCLAIM-36

•TCT1175 Terra Cotta Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Place waterproof sealer under each flange of the termina- tion cap and on top of each screw to help prevent leaks.

Termination Cap

The last section of pipe must stop between 2 in. (51 mm) above top of chase and 7 in. (178 mm) below top of chase

2 in. (51 mm)

7 in. (178 mm

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.7 Installing a TCT1175 Terra Cotta Cap

Heat & Glo • EXCLAIM-36, EXCLAIM-42 • 4013-251 Rev C • 11/08

37

Image 37

Hearth and Home Technologies EXCLAIM-36 owner manual TCT1175 Terra Cotta Cap

Contents

Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceFire Risk Grate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide CONDITIONS, Exclusions & Limitation of Liability Warranty Hearth & Home Technologies Limited Warranty Heat & Glo EXCLAIM-36, EXCLAIM-42 4013-251 Rev C 11/08 Appliance Certiﬁcation Listing and Code ApprovalsNon-Combustible Materials Combustible Materials Your Fireplace Operating InstructionsHot glass will cause burns Starting a Fire Seasoned WoodGrate Firescreen Vented Gas Log Sets & Gas Log Lighters Glass DoorsOptional Components Clear Space Wood Fuel Chimney Inspection/Cleaning Maintainance and ServiceDisposal of Ashes Creosote Formation and Need for Removal Check Firebox Refractory Glass CleaningInspect Grate Frequency As desired Start Fire Problems Possible Cause Solution Troubleshooting Guide Typical Fireplace System Getting Started Draft Design and Installation ConsiderationsNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & Chimney Fireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Select Fireplace Location Framing & Clearances Clearances to Combustible Materials Clearances Frame the Fireplace Sidewalls/Surrounds Unpack the Fireplace EXCLAIM-42 only Installation of FireplaceThings to Consider Unpack the Fireplace EXCLAIM-36 only Removing Smoke Shield Position the Fireplace EXCLAIM-42 only GAS Knockout Install the Refractory EXCLAIM-42 only Level Fireplace Place Protective Metal Hearth Strips YES Install Outside Air Kit Chimney Assembly Height of Chimney Components Chimney Requirements Example Using Offsets/Returns Assemble Chimney Sections Install Chimney Air Kit Installing the Ceiling Firestop Install Ceiling Firestops 330 mm Install Attic Insulation Shield Install Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in Roof Flat Roofs Chimney Termination Requirements Construct the Chase Chase Installations Install Chase Top Install Fireplace & Chimney ST1175/ST475 Square Termination Cap Install Termination Cap TCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shield Roofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Hearth Extension Construction Raised Hearth Extension Framing Flush Hearth Extension Framing Non-combustible Sealant Noncombustible Facing Finishing Material Combustible Mantel 19 3/4 502 mm Gas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1 Reference Materials Fireplace Dimensions EXCLAIM-36 EXCLAIM-42 Catalog # Chimney Components 15-1/4 387 mm 15-3/4 400 mm CT56 Chase Top LDS33/LDS46 Decorative Shroud EXCLAIM-36H, EXCLAIM-36T Service Parts EXCLAIM-42H, EXCLAIM-42T This page intentionally left blank Do not Discard this Manual