Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies EXCLAIM-36 C. Assemble Chimney Sections, D. Install Chimney Air Kit

Models: EXCLAIM-36

1 56

Download 56 pages 3.78 Kb

Page 29

C. Assemble Chimney Sections

C. Assemble Chimney Sections

WARNING! Risk of Fire! DO NOT install substitute or damaged chimney components.

•Use only those components described in this manual.

Substitute or damaged chimney components could impair safe operation and cause overheating and ﬁre.

•Support the pipe during construction and check to be sure inadvertent loading has not dislodged the chimney section from the ﬁreplace or at any chimney joint.

•Attach a straight chimney section or an offset to the top of the ﬁreplace.

•Place inner ﬂue to the inside of the chimney section below it. Place the outer casing outside the outer casing of the chimney section below it. Refer to Figure 8.4.

NOTICE: Chimney sections cannot be disassembled once locked together. Plan ahead!

•Lock chimney sections and/or offsets/returns together by pushing downward until the top section meets the stop bead on the lower section.

•Pull on the top section to make sure it is fully engaged and will not separate.

•You may use #6 or #8 sheet metal screws no longer than 1/2 in. (13 mm) to fasten chimney sections together. Do NOT penetrate inner ﬂue.

WARNING! Risk of Fire! You MUST use screws (pro- vided) to fasten offset/returns to chimney sections to keep the chimney parts from twisting. Failure to do so could cause ﬁre.

•Fasten offset/returns to chimney sections. Insert the screws (provided) through the predrilled holes. Do NOT penetrate inner ﬂue.

•Secure chimney returns with hanger straps provided; fasten to studs or joists.

•Vertical straight runs of chimney must be supported every 35 ft (10.7 m).

D. Install Chimney Air Kit

•Required in Canada.

•Follow instructions provided with this accessory.

Figure 8.4 Assembling Chimney Sections

Heat & Glo • EXCLAIM-36, EXCLAIM-42 • 4013-251 Rev C • 11/08

29

Image 29

Hearth and Home Technologies EXCLAIM-36 owner manual C. Assemble Chimney Sections, D. Install Chimney Air Kit

Contents

Models EXCLAIM-36 EXCLAIM-42 Wood Burning FireplaceOwner’s Manual Please retain this owner’s manual for future reference Read this manual before installing or operating this ﬁreplaceCongratulations Homeowner Reference InformationInstaller Guide Table of ContentsSafety Alert Key User GuideCONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY Warranty Hearth & Home Technologies LIMITED WARRANTYPage A. Appliance Certiﬁcation 1 Listing and Code ApprovalsB. Non-Combustible Materials C. Combustible Materials2 Operating Instructions User GuideA. Your Fireplace High temperatures may ignite clothing or other ﬂammable materialsC. Starting a Fire B. Seasoned WoodD. Grate E. FirescreenJ. Vented Gas Log Sets & Gas Log Lighters H. Glass DoorsK. Optional Components L. Clear SpaceHardwood vs Softwood M. Wood FuelMoisture Seasoned WoodB. Chimney Inspection/Cleaning 3 Maintainance and ServiceA. Disposal of Ashes Creosote - Formation and Need for RemovalC. Check Firebox Refractory E. Glass CleaningD. Inspect Grate CAUTION! Handle glass assembly with care. Glass is breakableStart Fire Problems 4 Troubleshooting GuideSolution Possible Cause5 Getting Started Installer GuideA. Typical Fireplace System Illustrations/diagrams are not drawn to scaleC. Draft B. Design and Installation ConsiderationsD. Negative Pressure NOTICE Check building codes prior to installationfrequently open doors central heat outlets or returns E. Locating Fireplace & ChimneyH. Inspect Fireplace and Components F. Tools and Supplies NeededG. Fireplace System Requirements Model 6 Framing & ClearancesA. Select Fireplace Location Figure 6.2 Clearances to Combustible Materials B. ClearancesD. Frame the Fireplace C. Sidewalls/Surrounds4 in 102 mmD. Unpack the Fireplace EXCLAIM-42 only 7 Installation of FireplaceA. Things to Consider B. Unpack the Fireplace EXCLAIM-36 onlyDO NOT install against vapor barriers or exposed insulation E. Position the Fireplace EXCLAIM-42 onlyWARNING! Risk of Fire! Prevent contact with sagging, loose insulation Secure insulation and vapor barriersGAS KNOCKOUT F. Install the Refractory EXCLAIM-42 onlyGRATE BRACKET GRATE BRACKETH. Level Fireplace G. Place Protective Metal Hearth StripsFigure 7.14 Position the Protective Metal Hearth Strips Figure 7.15 Protect the Front of an Elevated PlatformFigure 7.18 Outside Air Installation I. Install Outside Air KitFigure 7.17 Outside Combustion Air Placement Chimney height may need adjustment if smoking or overdraft occurs 8 Chimney AssemblyNOTICE Chimney performance may vary Trees, buildings, roof lines and wind conditions affect performanceÎ Table A. Chimney RequirementsWARNING! Risk of Fire! You must maintain 2 in NOTICE A maximum of two pairs of offsets and returns may be usedExample B. Using Offsets/ReturnsÎ Table Use only those components described in this manual D. Install Chimney Air KitC. Assemble Chimney Sections ATTIC ABOVE insulated ceiling Ceiling firestop from top E. Install Ceiling FirestopsROOM ABOVE non-insulated ceiling B A Ceilng firestop from bottom DO NOT offset chimney inside insulation shield F. Install Attic Insulation ShieldI. Install Flashing H. Complete InstallationG. Cut out Hole in Roof The following steps should be skipped if using a chaseFigure 8.10 Multiple Chimney Locations J. Chimney Termination RequirementsMultiple Chimney Locations WARNING! You must install false ceilings and ceiling 9 Chase InstallationsA. Construct the Chase C. Install Chase Top B. Install Fireplace & ChimneyCAUTION! DO NOT caulk the pipe to the chase top collarFigure 9.6 Installing an ST1175/ST475 Square Termination Cap Î D. Install Termination CapFigure 9.4 Installing a TR11/TR444 Round Termination Cap Heat & Glo EXCLAIM-36, EXCLAIM-42 4013-251 Rev C 11/08 Figure 9.7 Installing a TCT1175 Terra Cotta CapTCT1175 Terra Cotta Cap A. Radiation Shield 10 ShroudsB. Field Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shieldFigure 10.4 Roofed Style Shroud Dimensions Figure 10.3 Mailbox Style Shroud DimensionsMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredA. Non-Combustible Materials 11 FinishingB. Combustible Materials C. Hearth ExtensionFigure 11.2 Hearth Extension Construction Raised Hearth Extension FramingFigure 11.3 Raised Platform Hearth Extension Detail Figure 11.4 Raised Platform Hearth Extension-Framing MaterialsFlush Hearth Extension Framing Non-combustible SealantFigure 11.6 Place Non-combustible Sealant Figure 11.7 Flush Hearth ExtensionWARNING! Risk of Fire! You must maintain clearances D. Finishing MaterialUse only non-combustible framing material below standoffs DO NOT cover metal ﬁreplace front with combustible materialsEXCLAIM-36 E. Combustible Mantel12 in./305 mm EXCLAIM-424 in. 102 mm F. Sidewalls/Surrounds19 3/4 in 502 mmA. Gas Log/Lighter Provision 12 AccessoriesB. Wood Burning Inserts DO NOT install unvented gas logs13 Reference Materials A. Fireplace DimensionsEXCLAIM-36 B. Optional ComponentsEXCLAIM-42 DescriptionCatalog # C. Chimney Components15-1/4 in 387 mm B 17 in. 432 mm29 in 737 mmTR11T/TR442 - Round Telescoping Termination Cap TR11/TR444 - Round Termination CapTCT1175 - Terra Cotta Cap TR-TVK TR Top Vent KitCatalog # Catalog #CT56 Chase Top LDS33/LDS46 Decorative ShroudService Parts D. Service PartsService Parts EXCLAIM-36H, EXCLAIM-36TService Parts D. Service Parts continuedService Parts EXCLAIM-42H, EXCLAIM-42THeat & Glo EXCLAIM-36, EXCLAIM-42 4013-251 Rev C 11/08 This page intentionally left blankPlease contact your Heat & Glo dealer with any questions or concerns E. Contact InformationDO NOT DISCARD THIS MANUAL DO DISCARDNOT