Reference Materials | Hearth and Home Technologies PALOMA-GR

12 Reference Materials

A. Appliance Dimension Diagram Without Stone Surround

Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 3.

	A
			B			C
						D
	Height includes 3/8 in (9.53 mm) hearth pad
	E
			F
	G					I
		Hearth Pad
		H
	Location	Inches	Millimeter	Location	Inches	Millimeter
	A	18-7/8	479	F	7-1/8	181
	B	40-3/4	1035	G	30	762
	C	40-3/8	1025	H	28-7/8	733
	D	15-7/8	403	I	33-3/4	857
	E	3	76
Figure 12.1	Appliance Dimensions
52		Heat & Glo • Paloma • 7031-220 Rev. P • 10/08

Image 52

Hearth and Home Technologies PALOMA-GR Reference Materials, Appliance Dimension Diagram Without Stone Surround, Hearth Pad

Contents

Models What to do if you smell gasDo Discardnot Hot glass will cause burns Congratulations Homeowner Reference Information Table of Contents Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of Massachusetts Getting Started Installation to ensure maximum safety and beneﬁtTools and Supplies Needed Framing and Clearances Selecting Appliance LocationClearances to Combustibles Model Optional Stone Surround Installed Paloma Surround Vent Termination Minimum Clearances Termination LocationsSee .4 for speciﬁc clearances Alcove Applications Vent Information Venting ComponentsUse of Elbows Measuring Standards How to Use the Vent Graph SNKD, Horizontal InstallationVenting Guidelines Exception for Rear Vent KIT Snorkel Kit SLK Horizontal Termination Female Locking Lugs Male Locking 203 mm 178 mm 152 mm Vinyl Siding Vertical Termination Hole as shown in Figure Twist-lock the vent cap and seal Cathedral Ceiling Class a Metal Chimney Existing Masonry Chimney Type a To determine the length of flex needed, measure from Flex Liner Flex Coupler Sheet Metal Screws Slim Line Wall Thimble Installing Slim Line Trim Ring and Heat ShieldAssembling Slim Line Trim Ring and Heat Shield FIG. C Minimum Clearance Procedure for Conversion Gas InformationFuel Conversions Converting to LP Gas Reattach Pilot Shield Verify the performance of the ignition system Gas PressuresPressure Natural Gas Propane Gas Connection Check for GAS Leaks Recommendation for Wire Connecting to the ApplianceIntelliFire Ignition System Wiring Wire Size Max. Length Loss of Power and Battery Backup Usage Wall Switch Installation for Fan Optional Junction Box Wired to Wall Switch Remove Shipping Materials Appliance SetupUnbolting Appliance from the Pallet Accessories Leveling and Lagging Down the Appliance Top to Rear Vent Conversion Shutter Adjustment Installing the Vent Restrictor Installing the Bafﬂe Positioning the Logs Mineral Wool Installation precautionsOptional Blower Black Wires Recommended operating procedures Variable Installing flame control solenoid Remote ControlsRemote receiver Wiring the flame control solenoid RED Orange Blue Front Door Glass Assembly Installation Inner Glass Door Assembly Replacement Before Lighting Appliance Operating InstructionsControls Turn off all electric power to the appliance On position. The ON/OFF switch mayLighting Appliance IPI Ignition Final inspection by Initial Break-in Procedure Frequently Asked QuestionsAfter Appliance is Lit Symptom Possible Cause Corrective Action TroubleshootingIntelliﬁre Ignition System ﬂame has been lit, ﬂame Maintaining and Servicing Appliance Maintenance Tasks Inspect Maintenance Tasks Appliance Dimension Diagram Without Stone Surround Reference MaterialsHearth Pad Location Inches Millimeter Appliance Dimension Diagram With Stone Surround Appliance Dimensions with Stone Surround Vent Components Diagram SLP Series Vent Components Vent Components List Miscellaneous Log Set Assembly Service Parts Service Parts List StockedAt Depot Description Comments Part Number Stocked Bottom Plate Assembly Paloma CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information