Manuals / Hearth and Home Technologies / Household Appliance / Indoor Fireplace

Hearth and Home Technologies RUTHERFORD-50 Reference Materials, A. Fireplace Dimensions

Models: RUTHERFORD-50

1 52

Download 52 pages 33.52 Kb

Page 46

Image 46

14 Reference Materials

A. Fireplace Dimensions

11 in.

45 1/8 in. 281 mm

1146 mm

74° TYP.		27 1/2 in.

		699 mm

74 1/8 in.

1883 mm

Gas Line

Knockout

5in.

129 mm

16 1/8 in.

408 mm

6 7/8 in.

175 mm

11 1/8 in.

282 mm

50 in. 1270 mm

60 7/8 in.

1546 mm

70 3/4 in.

1797 mm

Gas Line

54 in.Knockout

1372 mm

38 in.	6 7/8 in.
965 mm	175 mm

3 3/4 in.	11 1/8 in.
97 mm	11 1/8 in.
	282 mm
	16 1/8 in.
	408 mm

5in.

129 mm

46	Heat & Glo • RUTHERFORD-50 • 4059-333 Rev F • 11/08

Page 46

Image 46

Hearth and Home Technologies RUTHERFORD-50 owner manual Reference Materials, A. Fireplace Dimensions

Contents

Owner’s Manual Models RUTHERFORD-50FIREPLACE Read this manual before installing or operating this ﬁreplaceDate purchased/installed MODELUser Guide Table of ContentsInstaller Guide Safety Alert KeyÎ Warranty Hearth & Home Technologies LIMITED WARRANTY CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITYPage install other than as instructed by Hearth & Home Technologies 1 Listing and Code Approvalsinstall or operate damaged ﬁreplace modify ﬁreplace install an unvented gas log setHigh temperatures may ignite clothing or other ﬂammable materials User Guide2 Operating Instructions A. Your FireplaceD. Grate B. Seasoned WoodC. Starting a Fire E. FirescreenJ. Vented Gas Log Sets & Gas Log Lighters DO NOT install unvented gas logs Damper must be locked openI. Glass Doors K. Optional ComponentsMoisture M. Wood FuelHardwood vs Softwood Seasoned WoodA. Disposal of Ashes 3 Maintainance and ServiceB. Chimney Inspection/Cleaning Creosote - Formation and Need for RemovalAvoid striking, scratching or slamming glass Avoid abrasive cleaners E. Glass CleaningCAUTION! Handle glass assembly with care. Glass is breakable Do not clean glass while it is hotSolution 4 Troubleshooting GuideStart Fire Problems Possible CauseA. Typical Fireplace System Installer Guide5 Getting Started Figure 5.1 Typical Fireplace SystemC. Draft B. Design and Installation ConsiderationsNOTICE Check building codes prior to installation D. Negative PressureE. Locating your Fireplace & Chimney DO NOT install in a basementfrequently open doors central heat outlets or returns G. Typical Fireplace Components F. Tools and Supplies NeededH. Inspect Fireplace and Components A. Select Fireplace Location 6 Framing & ClearancesNOTICE Both outside air kits MUST be installed Model #B. Clearances Figure 6.2 Air Space ClearancesC. Sidewalls/Surrounds angleD. Frame the Fireplace A. Things to Consider 7 Installation of FireplaceDO NOT install against vapor barriers or exposed insulation B. Position the FireplaceInstall as shown in Figures 7.3, 7.4 and E. Install Outside Air KitThe outside air kits must be installed on both sides of the ﬁreplace Keep duct runs short and straight to minimize restrictionNOTICE Chimney performance may vary 8 Chimney AssemblyChimney height may need adjustment if smoking or overdraft occurs Trees, buildings, roof lines and wind conditions affect performanceused A. Chimney RequirementsNOTICE A maximum of one offset and return may be WARNING! Risk of Fire! You must maintain 2 in. 51 mmFraming Dimension C. Installation NotesF. Install Firestop B. ClearancesH. Supplementary Support and Stabilizer G. Assemble Chimney SectionsChase Frame Stabilizer Plumbers Tape Attic I. Install Attic Insulation ShieldJ. Install Roof Radiation Shields FirestopL. Enclosures M. Offset Elbow InstallationK. Finish Top Sealant CollarMultiple Chimney Locations N. Chimney Termination RequirementsFigure 8.18 Multiple Chimney Locations stop opening and chimney pipe except where they enter the 9 Chase InstallationsWARNING! You must install false ceilings and ceiling A. Construct the ChaseD. Install Termination Cap B. Install Fireplace & ChimneyC. Install Chase Top Flashing Storm collar must be installed 1 1/2 in off chase top10 Shrouds A. Shroud RequirementsHouse Style Shroud Minimum Dimensions B. House Style ShroudC. Arch / Mailbox Style Shroud Arch / Mailbox Style Shroud Minimum DimensionsPyramid Style Shroud Minimum Dimensions D. Pyramid Style ShroudB. Install Side Molded Brick Panel-Traditional 11 Installation of Molded Brick PanelA. Install Hearth Molded Brick Panel C. Install Back Molded Brick Panel-TraditionalE. Install Back Molded Brick Panel-Herring- bone D. Install Side Molded Brick Panel-Herring- boneFigure 11.2 Herringbone Molded Brick Panel G. Install Screens F. Install MortarTools Required Hearth extensions MUST be installed exactly as speciﬁed 12 FinishingMetal hearth strips MUST be installed Section 7.C A. Non-Combustible MaterialsFraming Material Raised Hearth Extension FramingNoncombustible equivalent insulationFlush Hearth Extension Framing Non-combustible SealantNon-combustible Sealant Use only non-combustible framing material below standoffs D. Finishing MaterialWARNING! Risk of Fire! You must maintain clearances DO NOT cover metal ﬁreplace front with combustible materials2 x 4 stud header Standoffs E. Combustible MantelCombustible Wall Combustible Decorative Facing Notches2 in 51 mm F. Mantel, Adding Extra SupportNotches both ends Notches in standoffs18 1/2 in. 470 mm G. Sidewalls/SurroundsDamper must be locked fully open when gas logs are installed 13 AccessoriesDO NOT install unvented gas logs A. Gas Log/Lighter Provision14 Reference Materials A. Fireplace DimensionsCatalog # B. Optional ComponentsC. Chimney Components DescriptionService Parts D. ServiceService Parts IMPORTANT THIS IS DATED INFORMATION. When requesting service orThis page intentionally left blank Heat & Glo RUTHERFORD-50 4059-333 Rev F 11/08This page intentionally left blank Heat & Glo RUTHERFORD-50 4059-333 Rev F 11/08This page intentionally left blank Heat & Glo RUTHERFORD-50 4059-333 Rev F 11/08DO NOT DISCARD THIS MANUAL E. Contact InformationPlease contact your Heat & Glo dealer with any questions or concerns DO DISCARDNOT