F.Installation Instructions and Venting In- formation - PVI-DVP

These instructions are for appliances utilizing the PVI-DVP. For appliances incorporating the PVK-80, see Section 7.J.

IMPORTANT: Failure to read and follow these instruc- tions may create a possible hazard and will void the fire- place warranty.

CAUTION! Risk of Cuts or Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

INTRODUCTION

The PVI-DVP is certified for use only on fireplaces manufac- tured by Hearth & Home Technologies with IPI (intermittent pilot ignition) gas controls.

The PVI operates on 120VAC, 60Hz electrical service which is supplied at the fireplace junction box.

Components and Service Parts List

Service Parts List

Replacement parts can be obtained from your dealer. Re- pair of the Power Vent should only be done by a qualified service technician. A list of replacement parts is shown in the service parts section of this manual.

INSTALLATION OF PVI-DVP

1. INSTALLATION PRECAUTIONS

a.This device must be installed by a qualified installer in accordance with these instructions.

b.Safety inspection of the venting system should be performed before and after installation of this power vent. Consult local code officials and follow applicable installation codes.

c.DO NOT INSTALL DAMAGED EQUIPMENT OR VENT COMPONENTS.

d.The exit termination of mechanical draft systems shall not be less than seven feet above grade when located adjacent to public walkways and at least ten feet from lot line or adjacent buildings.

e.A mechanical drafting venting system shall terminate at least three feet above any forced air inlet located within ten feet.

f.Disconnect electrical power supply before making wiring connections.

g.Venting of more than one appliance in a common vent system is prohibited.

h.Clearances between the vent pipe and combustible ma- terials must be maintained at 3-inch top, 1-inch sides, and 1/2 inch bottom.

i.All outer pipe joints must be sealed with high tempera- ture silicone. See Section10.A.

CAUTION: Failure to install, operate, and maintain the power venting system in accordance with manufacturer's instructions will result in conditions which may produce bodily injury and/or property damage.

NOTICE: The blower motors present in this appliance will generate sound during operation. The effects of the increased sound level can be minimized with careful planning during installation of the system. Locating the powervent service access grill in an area remote of immediate living space will reduce the effects of the added sound generated during operation.

2. INSTALLATION GUIDELINES

WARNING: RISK OF FIRE AND BURNS. DO NOT in- stall PVI with the access panel facing upward. Over- heating may occur.

a.If the PVI-DVP is being installed in a confined space (such as a utility closet, mechanical room or attic space) with a total volume less than 720 cubic ft, an 8 inch by 16 inch hole will be required directly in front of the access panel. The confined space where PVI is installed, and the space to which the access hole opens, must add up to at least 720 cubic feet. This hole may be covered with a decorative cover as long as the cover has a minimum of 50% open air. This also applies to a fireplace chase.

If the PVI-DVP is being installed in a space greater than 720 cubic ft the 8 inch by 16 inch access hole is still required, but a solid cover may be used.

The decorative cover CANNOT be located on an outside wall that is open to the environment.

b.For installations near loose-fill insulation (such as attics) a minimum clearance of six inches must be maintained between the access panel and the insulation.

c.The access panel opening must be located such that access for service and adjustment is available. The NEC requires a minimum of 30 inches of space around the opening and 36 inches in front of the opening to the access panel. Consult officials having jurisdiction regarding regional requirements.

Heat & Glo • RED60 • 2159-900 Rev. R • 9/12

23

Page 22 Page 24
Page 23
Image 23
Heat & Glo LifeStyle RED60 2159-900 Installation Instructions and Venting In- formation PVI-DVP, Installation Precautions
Page 22 Page 24

RED60 2159-900 specifications

The Heat & Glo LifeStyle RED60 2159-900 is a modern and innovative gas fireplace that exemplifies cutting-edge design and advanced heating technology. With its sleek aesthetics and smart features, this fireplace is designed to elevate both comfort and style in any living space.

One of the main features of the RED60 is its impressive heat output. This model boasts a high efficiency rating, ensuring that homeowners can enjoy warmth without excessive energy consumption. The fireplace can deliver an output of up to 60,000 BTUs, making it suitable for both large and small areas. This efficient performance means less environmental impact, aligning with the growing emphasis on sustainability in home heating solutions.

The design of the Heat & Glo LifeStyle RED60 is another standout aspect. Its expansive glass viewing area provides a panoramic view of the flames, creating a beautiful focal point in any room. The minimalist frame enhances the contemporary aesthetic, allowing it to seamlessly complement various interior styles, from modern chic to traditional elegance.

In terms of technology, the RED60 incorporates advanced combustion systems, ensuring cleaner emissions without sacrificing performance. This technology not only contributes to a healthier indoor environment but also helps reduce the carbon footprint associated with home heating. Additionally, the fireplace features a patented heat distribution system, which optimally circulates warmth throughout the space, eliminating cold spots and enhancing overall comfort.

The RED60 also offers convenience through its intuitive remote control system. Users can easily adjust the flame height, heat output, and even set timers, providing ultimate flexibility in managing their indoor climate. For those who prefer a more hands-on approach, manual controls are also available, making it user-friendly for everyone.

Moreover, the installation process is simplified with the unit's flexible venting options, which can accommodate various configurations to suit different homes. Whether designing for a new build or retrofitting an existing space, this versatility appeals to homeowners and builders alike.

In summary, the Heat & Glo LifeStyle RED60 2159-900 is a blend of style, efficiency, and advanced technology. Its high heat output, sleek design, and intuitive controls make it an excellent choice for anyone seeking to enhance their living environment with a modern gas fireplace.
Top Page Image Contents