Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle st-42tvfl manual Step Wiring the Fireplace, When Servicing Controls. Wiring

Models: st-42tvfl

1 31

Download 31 pages 25.27 Kb

Page 24

Step 9

Step 9

Wiring the

Fireplace

NOTE: Electrical wiring must be installed by a licensed electrician.

Caution: Disconnect remote controls if you are absent for extended time periods. This will prevent accidental fireplace operation.

For Standing Pilot Ignition Wiring

Appliance Requirements

•This appliance DOES NOT require 110-120 VAC to operate.

WARNING

!DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE WALL SWITCH OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional remote control kits require that 110-120 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Wall Switch

Position the wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/OFF switch pigtails.

!WARNING

DO NOT CONNECT 110-120 VAC TO THE WALL SWITCH OR THE CONTROL VALVE WILL BE DESTROYED.

CAUTION	LABEL ALL WIRES PRIOR TO DISCONNECTION
	WHEN SERVICING CONTROLS. WIRING
	ERRORS CAN CAUSE IMPROPER AND
	DANGEROUS OPERATION. VERIFY PROPER
	OPERATION AFTER SERVICING.

	BLACK L1	BLACK L2
		HI-TEMP LIMIT SWITCH
		REMOTE SWITCH
GAS VALVE		PIGTAIL
GAS VALVE
		ON
		OFF
	WHITE T2	ON/OFF SWITCH
	WHITE T2
	RED T1
	THERMOPILE
THERMOCOUPLE	BLACK S1	OPTIONAL WALL SWITCH,
	BLACK S1	OPTIONAL WALL SWITCH,
		THERMOSTAT OR REMOTE

24

Figure 11. Standing Pilot Ignition Wiring Diagram

Image 24

Heat & Glo LifeStyle st-42tvfl Step Wiring the Fireplace, When Servicing Controls. Wiring, Errors Can Cause Improper And

Contents

Models PIER-TVFL ST-42TVFL Installers GuideSAFETY AND WARNING INFORMATION THIS UNIT IS NOT FOR USE WITH SOLID FUELTable of Contents Service Parts PIER-TVFL, PIER-TVFL-DSI1 4 7 Log AssemblyACCESSORIES / ACCESSOIRES PIER-TVFLand PIER-TVFL-DSI1 5 4 2 3 5 1 7Service Parts 6Log AssemblyST-42TVFLand ST-42TVFL-DSI Service Parts PIER-TVFL, ST-42TVFL Standing Pilot IgnitionService Parts PIER-TVFL-DSI, ST-42TVFL-DSI 4 125 10 Direct Spark IgnitionApprovals and Codes and CodesInstallation Codes High Altitude InstallationsPre-installationPreparation Introducing the Heat-N-Glo Gas FireplacesGetting Started ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARDFigure 1. Diagram of the Pier-TVFL Figure 2. Diagram of the ST-42TVFL LEFT SIDEFRONT Installing the Fireplace Step Locating the FireplaceClearance Requirements Step Framing the Fireplace MEASURE FIREPLACE DIMENSIONS, ANDVERIFY FRAMING METHODS AND WALL COVERING DETAILS, BEFORE FRAMINGStep Negative Pressure Make-upAir ASSEMBLY Air DamperFigure 5. Make-upAir DUCT COLLARStep Installing the Vent System A. Vent System ApprovalsB. System Components MAXIMUM NO. of ELBOWS: 2 - 90o or 4 - 45oFigure 6. Vent System Attachment C. Bedroom Installation in Canada Step Positioning Leveling, and Securing the FireplaceStep The Gas Control Systems Step The Gas Supply Line Step Gas Pressure Requirements Figure 10. Gas Supply LinePressure Natural GasStep Wiring the Fireplace WHEN SERVICING CONTROLS. WIRINGERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPERFor Direct Spark Ignition DSI Wiring Optional AccessoriesWall Switch LABEL ALL WIRES PRIOR TOStep Finishing Step Installing Trim Logs, and Ember Material Installing the TrimHearth Extensions GLASS SPECIFICATIONS LARGE GLASS: TEMPERED Figure 15. Placement of the Ember MaterialSMALL GLASS: TEMPERED Placing the Ember MaterialLighting the Fireplace After the Installation Step Before Lighting the Fireplace StepFireplace Maintenance Maintaining and Servicing Your FireplaceFireplace Maintenance Task To MaintenanceMAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATINGSTANDING PILOT 3/8 10mm DSI IGNITION IGNITOR